Land Rover Brake Discs: All Models In Stock

Platform Load and Wear Patterns

How Land Rover brake systems load and wear

Brake-component wear on a Land Rover or Range Rover follows the platform. Discovery 3, Discovery 4, and Range Rover Sport L320 share the IBF chassis architecture and similar braked-mass figures, with Discovery 3 kerb weight running from 2,394 to 2,536 kg across variants. That mass loads pads and discs predictably under repeated use, and pad compound choice matters more than it does on a lighter vehicle.

Range Rover L405 and Range Rover Sport L494 share the D7u aluminium platform and continue the heavy-platform pattern. Defender Classic and the new Defender L663 sit on different architectures but share the same off-road exposure factor: mud, water, and grit accelerate caliper piston binding and pad wear in ways that road-only platforms don't see. Freelander 1 and Freelander 2 are lighter and front-biased; the most common brake-side service item is handbrake cable replacement on both generations.

Series 2 and Series 3 use mechanically simpler hydraulic brake systems with no electronic actuation, but correct component pairing (disc, pad, caliper seal kit) still determines whether the brake job lasts.

Collection Scope

What this collection covers

The Land Rover Brake Parts collection holds:

Brake discs and rotors for all generations, listed under Land Rover brake discs
Brake pads in OEM-grade and performance compounds, listed under Land Rover brake pads
Brake calipers, caliper rebuild seal kits, and guide pin sets
Electronic Parking Brake (EPB) actuators, gear repair kits, and switches for Discovery 3, Discovery 4, Range Rover Sport L320, and L405-platform vehicles
ABS wheel-speed sensors, ABS modules, and related wiring
Brake fluid (DOT 4 and DOT 5.1 grades) and bleeding kits
Handbrake cables for Defender, Freelander 1, and Freelander 2

For brand-specific filtering, Ferodo brake parts and TRW brake parts are listed under their own collections within this category.

Pre-Purchase Fitment Checks

Before you order

Brake parts are usually replaced as a matched system, not as individual components. A buyer ordering pads alone for a Discovery 4 or Range Rover L405 typically generates a comeback within a service interval. Check the following before placing an order:

Match pads and discs as a pair. New pads on worn discs cause vibration on heavier platforms (Discovery 4, L322, L405) and shorten pad life. Pad-material transfer to the disc surface is uneven when the disc is already heat-cycled and out of spec for thickness.
Replace pad-wear sensors at the same time. Reusing old sensors on Discovery 3, Discovery 4, Range Rover Sport L320, L405 or L322 generates near-immediate dashboard warnings even when the new pads have full life.
Confirm caliper guide pin condition. Off-road-used Defender and Freelander calipers commonly seize at the guide pin or piston, particularly after winter use. Inspect before assuming pads and discs alone will fix uneven wear or pulling under braking.
Verify EPB system status before ordering rear brake parts. Discovery 3, Discovery 4, Range Rover Sport L320, and L405 require the EPB to be placed into service mode using a diagnostic tool before the rear caliper can be retracted. Ordering rear pads without this capability or workshop access leads to delayed or damaged installation.

Pro-Tip

The EPB on Discovery 3, Discovery 4, Range Rover Sport L320, and L405 cannot be retracted manually for pad replacement. The system must be placed into service mode using a diagnostic tool (Land Rover diagnostic tools). Ordering rear pads without service-mode access usually means a delayed fit, not a quick replacement.

Common Ordering Mistakes

Common Land Rover brake-parts ordering mistakes

These are buyer-side patterns that generate avoidable comebacks. None of them are diagnosis or repair procedures. They are part-selection patterns.

Mixing pad compounds across an axle. A worn pad replaced with a different compound on the opposite side of the axle causes pulling under braking on Defender, Discovery, and Range Rover models alike. Order matched-set pads, not single pads.
Reusing old wear sensors with new pads. The sensor is a consumable. On Discovery 3, Discovery 4, Range Rover Sport L320, L405, and L322, a reused sensor will trigger a dashboard warning within hours of a successful pad replacement.
Ordering discs alone without confirming pad thickness. A disc replacement on a Range Rover L405 or Discovery 4 with pads at 30% or below means a second job within months. Inspect pad life when discs are ordered.
Generic non-ECE R90 friction parts on EU vehicles. Replacement brake pads and discs sold for road use in the EU must hold an ECE R90 approval mark. Workshop and trade buyers benefit from filtering by Ferodo brake parts or TRW brake parts, both of which carry R90 approval on relevant part numbers.

System Adjacency

Brake parts and adjacent systems

Brake replacement on Land Rover models often touches adjacent systems that wear on similar cycles.

Wheel bearings. Heavier-platform Discovery 4 and Range Rover L405 hubs commonly show bearing wear at the same service interval as a major brake job. Pull a wheel for the brake job and check for bearing play before reinstalling. Land Rover wheel bearings are listed separately.
Suspension bushings and arms. Degraded lower control arm bushings on Range Rover L322, L405, and Range Rover Sport L320 change the wheel's geometry under braking, accelerating uneven pad and disc wear. Land Rover suspension parts cover the inspection items worth checking during a brake job.
Handbrake cables on Defender and Freelander. Defender, Freelander 1, and Freelander 2 commonly need handbrake cable replacement before the brake shoes themselves. Stretched or seized cables generate inspection failures and reduce holding force on inclines.

EU Regulatory Compliance

ECE R90: what replacement brake parts must meet in the EU

Brake pads, brake discs, and brake drums sold as aftermarket replacement parts for vehicles type-approved after the relevant cut-off date must hold ECE Regulation 90 approval. The regulation requires replacement pads to perform within a 15% tolerance of original equipment friction characteristics, and applies to brake discs for passenger cars registered after November 2016 and to brake pads since 1 January 1999. ECE R90 approval is the baseline for EU road use, not a premium tier.

EU Stock and Dispatch

EU stock from the Netherlands

Brake parts in this collection are held in the Dutch warehouse network for EU dispatch. EU buyers pay no customs charges or VAT surprises on inbound delivery. Trade and workshop buyers can access the wholesale portal for trade pricing and dedicated account support.

Technical Guides

Related diagnostic and service guides

Land Rover EPB service guide

Discovery 3, Discovery 4, and Range Rover Sport L320 EPB failure is usually traced to worn rear brake shoes or stretched handbrake cables, not the actuator motor itself. The diagnostic and repair path covered in this guide explains what fails first and which parts are commonly needed.

Discovery EPB fault diagnosis

Range Rover Sport L320 air suspension

The L320 air suspension and brake systems share heavy-platform wear patterns, particularly on vehicles used for towing or heavy load. This guide covers the compressor, air spring, and suspension component failures most often seen alongside or shortly before a major brake service.

Range Rover Sport L320 air suspension guide

FAQs

Frequently asked questions

Are aftermarket brake pads and discs legal for use on Land Rover vehicles in the EU?

Yes, provided they hold ECE Regulation 90 approval. ECE R90 has been mandatory for replacement brake pads on EU-registered passenger vehicles since 1 January 1999, and for replacement brake discs since November 2016. R90-approved aftermarket pads must perform within 15% of the original equipment's friction characteristics. Both Ferodo and TRW brake parts in this collection carry R90 approval on relevant part numbers.

Do I need a diagnostic tool to change rear brake pads on a Discovery 3, Discovery 4, Range Rover Sport L320, or Range Rover L405?

Yes. The Electronic Parking Brake must be placed into service mode using a diagnostic tool before the rear caliper piston can be retracted. Attempting to retract the caliper without service mode can damage the EPB actuator. Workshop access or a compatible diagnostic tool is a prerequisite, not optional, for rear brake replacement on these platforms.

What's the difference between OEM-grade brake pads and performance brake pads for Land Rover models?

OEM-grade pads target the original friction characteristics of the vehicle: predictable bite, consistent fade resistance, and acceptable pad life under normal road use. Performance pads typically use a higher-temperature friction compound and are intended for towing, sustained heavy load, or off-road use on Defender, Discovery, and Range Rover platforms. Performance pads can be noisier and may wear faster under normal driving. Match the pad to how the vehicle is actually used.

Can I order brake pads or discs without knowing my Land Rover's exact model year?

We recommend checking the model year and engine variant before ordering. Brake-component sizing varies by generation (Discovery 3 versus Discovery 4 versus Discovery 5), by engine option (heavier engines often run larger discs), and by trim level on Range Rover variants. The VIN or chassis plate is the most reliable identifier for fitment lookup. The chassis plate sits on the A-post or near the bulkhead, depending on market variant (LHD versus RHD).

Do you stock brake parts for Series 2 and Series 3 Land Rovers?

Yes. Series 2 and Series 3 brake components, including drum brake parts and the hydraulic-only system items, are listed within the brake-parts collection. Series vehicles use mechanically simpler systems with no electronic actuation, but correct disc, pad, and caliper-seal pairing still determines how long the brake job holds.