Land Rover Parts

Bonnet Hinge Bush for the Land Rover bonnet hinge assembly. This bush fits into the bore of the bonnet hinge, providing a wear surface around the ...

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Oil Filter for Land Rover petrol and diesel engines, part of the engine lubrication circuit. This screw-on canister filter threads onto the filter...

Sump Gasket - 4-Cyl for the engine sump sealing joint on Land Rover 4-cylinder engines. This gasket seals the mating face between the sump pan and...

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Body Panel Locknut for square-hole panel apertures, used in body, interior, and trim panel assemblies. This push-fit captive nut locates into a sq...

Hub Oil Seal - Inner for the front and rear wheel hubs, seating around the stub axle. The seal runs on the stub axle to retain hub lubricant and e...

Indicator Switch mounted on the steering column, combining the direction-indicator, headlamp dip and horn functions in a single column stalk contro...

Sump Plug Washer - copper sealing washer for the sump drain plug and thermostat housing on petrol and early diesel engines. The copper washer seat...

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This is the pl...

Joint washer exhaust TD5

Nyloc Nut with a 3/8" UNF thread, used to secure propshaft flange bolts. A nylon insert set into the crown of the nut deforms over the bolt thread...

Rocker Cover Gasket - Diesel for the 2.25L and 2.5L 4-Cylinder diesel engine. This gasket seals the joint between the rocker cover and the cylinde...

Side Lamp - front side (parking) lamp in the exterior lighting system. Dome-type front side lamp providing position and marker lighting at the fro...

Rear Light Lens for the rear stop and tail lamp. The red lens fits over the lamp body to cover the stop and tail bulb, transmitting the brake ligh...

Clutch Slave Cylinder is the hydraulic actuator in the clutch release circuit, mounted externally on the gearbox bellhousing. When the clutch peda...

Brake Drum Screw for the brake drum assembly. This retainer screw secures the brake drum to the wheel hub flange, preventing the drum from displac...

Rocker Cover Gasket seals the joint between the rocker (valve) cover and the cylinder head at the top of the engine, within the valvetrain assembly...

Clutch Pedal Return Spring is a tension spring within the clutch pedal assembly that returns the pedal to its resting position after the driver rel...

Hub Cap fits over the end of the front or rear hub, enclosing the drive flange and hub assembly. It closes off the outer end of the hub to retain ...

Pedal Pad - Brake & Clutch is the moulded rubber cover that fits over the pedal arm, giving the driver's foot a grippy contact surface. The ri...

Hub Bearing - a tapered roller bearing for the front and rear axle wheel ends. It supports the rotating wheel hub on the stationary stub axle, carr...

Propshaft Bolt - a fastener that secures the propshaft universal-joint flange to the differential drive flange within the driveline. It clamps the...

Transfer Box Output Flange Oil Seal is a radial shaft seal fitted at the output flange of the LT230 transfer box, sealing between the rotating outp...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Indicator Lamp Lens, amber, for the round-type direction indicator (turn signal) lamp. The lens fits over the lamp body to seal and protect the bul...

Door Mirror supplied as a complete unit comprising the mirror head and its mounting arm, for external door mounting to give rearward visibility fro...

clutch master cylinder OEM Delphi

Wheel Cylinder for the drum brake assembly - the left-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either ...

Spiralok Nut for body panel and interior trim fixings. This spring-steel speed nut (clip nut) clips to a panel flange or through a mounting hole a...

Oil Filter for the engine lubrication system of the 2.25L four-cylinder petrol and diesel engine. The filter traps combustion by-products, metal p...

Clutch Master Cylinder Copper Washer for the hydraulic clutch system. Copper sealing washer used at the adaptor connection between the clutch hydr...

Sump Plug Sealing Washer for the engine lubrication system. It seats between the oil drain plug and the sump pan boss, sealing the joint so the plu...

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Swivel Joint Washer located within the Swivel Pin Housing Assembly, sealing the interface between the swivel housing flange and the axle beam face....

Fir Tree Fastener - a one-piece plastic push-in clip that secures front-end trim and cap panels without threaded fixings. The barbed, fir-tree rib...

Thermostat Housing Gasket in the engine cooling system. This gasket seals the thermostat housing to its mating surface on the engine, preventing c...

Fuel Injector Harness for the Td5 fuel injection system, carrying the electrical connection between the engine wiring loom and the electronic unit ...

Thermostat Housing Gasket for the engine cooling system. This top gasket seals the joint between the thermostat housing and the engine, preventing...

Master Lighting Switch - column-mounted master switch controlling the primary exterior lighting circuits. Mounted within the steering column switc...

Steering drop arm lever for left-hand drive steering box applications. This component connects the steering box output shaft to the steering linka...

Number Plate Lamp for the rear number plate lighting circuit. This complete lamp assembly mounts at the rear of the vehicle to illuminate the numb...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Windscreen Washer Jet Assembly - nozzle assembly for the windscreen washer system, mounted on the scuttle or bonnet to spray washer fluid onto the ...

Major Service Kit for the 2.5L Td5 engine, containing the filtration and service consumables for a full scheduled service. Kit contents: 1 x oil f...

Fan Belt for the engine auxiliary (accessory) drive. Transmits drive from the crankshaft pulley to the water pump, cooling fan and dynamo or altern...