Land Rover Parts

Filler Pipe Securing Ring for the fuel filler pipe assembly. This retaining ring secures the fuel filler pipe to the fuel tank inlet, maintaining ...

Blanking Plug for the cylinder block. It seals a machined port in the engine casting where no sensor, sender or fitting is installed, preventing co...

Headlamp Bulb Cover for the front headlamp assembly. This rubber cover seals the bulb access aperture at the rear of the headlamp unit following b...

Radio Surround Panel is the lower fascia surround that frames the audio head unit aperture in the centre console of the Range Rover P38. It sits w...

Kit - Boot

Fuel Filter for the TD4 2.0L diesel engine fuel system. This filter element installs within the fuel filter housing in the engine bay fuel circuit...

Rear Fog Lamp Lens for use in the rear lighting unit assembly. This component forms the outer optical element of the fog lamp housing, positioned ...

Red Glass Lens - a replacement lens for an exterior lamp unit. The lens seats over the lamp body to seal the bulb chamber and colour the emitted l...

Wheel Centre Cover fits into the central hub bore of an alloy wheel, concealing the hub and wheel-mounting hardware behind a finished cap that clip...

Mud Flap Bracket for the right-hand rear position on High Capacity Pick Up (HCPU) bodywork. Part of the exterior mud flap mounting. The HCPU rear ...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Camshaft Washer is a retaining washer used at the front of the camshaft within the timing drive of the 3.5L V8 petrol engine. It is fitted at the ...

Steering Column Moulding for the Defender interior. This plastic moulding fits around the base of the steering column, providing a neat trim finis...

Sealing Strip is a windscreen glazing seal, supplied as a pair, forming part of the windscreen glazing assembly. The strips seal the windscreen gl...

TDi Decal for Defender 110. Original-specification exterior decal carrying the TDi designation. Applied to the body as part of the standard factor...

Bulb Holder is the bulb and holder assembly that provides the illumination for the clock and cigar lighter on the centre console. The holder seats...

Control Unit - dim dip lighting module for the Defender electrical system. This module operates the dim dip lighting circuit, activating the headl...

Remote Handset Case - replacement housing for the remote locking plip (key fob), supplied as the case only without the internal electronics. House...

Hexagon Nut for use in electrical system assemblies.

Rocker Cover Screw for the Rover V8 petrol engine. This 1/4" UNC screw secures the valve (rocker) cover to the cylinder head. The rocker cover per...

Bolt, high tensile, M8 x 25mm. A metric hexagon head bolt for body, chassis, and structural fastening applications.

Clutch Damper for the Defender Puma hydraulic clutch circuit. This in-line hydraulic damper installs within the clutch hydraulic hose run between ...

Hazard Switch Bulb Illumination bulb for the hazard warning switch within the facia switch assembly. It provides the internal lighting that illumi...

Sealing Washer fitted at the engine front cover. Provides a leak-tight seal at a fastener or fitting on the front cover assembly.

Battery Terminal Nut - a replacement fastener for the battery terminal clamp bolt. Used to secure the positive or negative cable clamp firmly onto...

Anti-Burst Lock - right-hand tailgate latch assembly. The anti-burst design captures the striker pin within a rotating claw, holding the door close...

Brake Caliper Guide Pin Set for the sliding (floating) disc brake caliper assembly. The guide pins locate the caliper to its mounting bracket and a...

Wastegate Control Hose for the 2.5L 200 TDi turbo diesel engine. This hose forms part of the turbocharger boost-control circuit. It routes the boo...

Conrod Bearing Set (big-end bearings) for the 2.6L 6-cylinder petrol engine. The shells sit between the connecting-rod big-ends and the crankshaft...

Tailgate Cable Stud is the anchor point for the rear tailgate support cable. Mounted on the rear body, the stud receives the end of the tailgate c...

Tailgate Hinge Bracket Cover - trim cover for the rear tailgate hinge bracket. The cover fits over the tailgate hinge bracket, concealing and prot...

Exhaust Bracket for the rear section of the Range Rover Classic twin pipe exhaust system. This bracket mounts to the chassis and secures the rear ...

Front Seat Armrest Finisher, the decorative trim panel forming the visible outer surface of the front seat armrest on the Discovery 2. Applies to ...

Differential Pinion Bearing Shim - 0.068 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Differential Pinion Bearing Shim - 0.066 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Truck Cab Waist Seal for the Land Rover Defender truck cab body variant. This rubber seal fits at the waist level of the truck cab body, sealing t...

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Battery Fixing Stud - Long Straight is a long straight J-bolt used to secure the battery retaining clamp to the battery tray. The stud passes thro...

Negative Battery Cable forms part of the vehicle's electrical earthing circuit. It connects the battery negative terminal to the vehicle earth poi...

Fusible Link is a high-current circuit-protection device fitted in the engine compartment fuse box. It protects heavy-current wiring and the downs...

Washer for use in general fastening applications across the Defender and Range Rover Classic. This plain washer distributes clamping load across t...

Shakeproof Starlock Washer used within the clutch master cylinder and pipe assembly. The washer pushes onto a plain shaft or pin and grips it with...

Circlip - Driveshaft Boot is a retaining circlip used within the driveshaft CV joint boot assembly. The circlip secures components within the CV j...