Land Rover Parts

Clip - a small retaining clip used within the transfer box differential lock linkage and at the handbrake lever and clutch master cylinder mounting...

U-Type Spring Nut for the fascia (dashboard) assembly and mounting brackets. Spring-steel clip-on nut that grips a panel edge to provide a captive...

Bolt used in the LT95 gearbox and transfer assembly. It provides a torque-loaded, clamped fastening securing components within the LT95 transmissi...

Snap Ring

PTO Selector Cover Plate - a blanking plate for the power take-off (PTO) selector aperture on the transfer box. It covers and seals the selector o...

Engine & Gearbox Mount - Lower The lower (bottom) rubber mounting that isolates the engine and gearbox from the chassis, absorbing running vibr...

Fuel Pump Gasket seals the external fuel pump to its mounting face in the fuel delivery system, preventing leakage at the joint. Used on petrol ap...

Bolt is a hex-head threaded fastener used to secure components at bolted joints, such as engine and starter-motor mountings.

Reverse Gate Bracket is the fixed section of the reverse-gate stop within the gear-lever mounting on the Series four-speed gearbox. It forms the g...

Caliper Seal - Rear

Radiator Hose – Bottom for the engine cooling system. The bottom radiator hose returns cooled coolant from the base of the radiator to the engine,...

Foam Gasket seals the door lockface, part of the door latch and lock assembly. It fits between the latch mechanism and the lockface panel, sealing...

Sill Lock Escutcheon trim surround for the door push-button lock mechanism, in brown. This escutcheon fits over the door sill lock button, providi...

Handbrake Gaiter for the handbrake lever assembly in Series II, IIA, and III Land Rovers. Fits 109-inch wheelbase V8-engined variants. The gaiter ...

Wheel Nut Cover Removal Tool for removing and refitting plastic wheel nut covers. This purpose-made tool engages the decorative plastic caps fitte...

Wiper Hole Blanking Plug - Plenum Air-Take Extension for the Discovery 2 (L318). This rubber blanking plug seals an unused aperture in the plenum ...

Door Handle Cap - LH is the left-hand end cap for the exterior front door handle assembly, incorporating the lock barrel aperture. The cap forms t...

Heater Hose - Heater Matrix to Control Valve forming part of the engine cooling and cabin heating circuit. This hose runs between the heater matri...

Heater Control Pin

Blanking Plug

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Door Check Bracket - Rear is a mounting bracket within the rear door check mechanism. It anchors the door checker (door stay) to the body, providi...

Heater Hose - Coolant Valve is a moulded coolant hose in the heater circuit of the engine cooling system. It connects the heater control (coolant)...

Fan Cowl Clip is a retaining clip in the engine cooling system. It secures the fan cowl - the shroud that channels airflow through the radiator - ...

Piston ring set petrol 2,25 020 Mahle (per zuiger)

Radiator Hose – Bottom for the engine cooling system. The bottom radiator hose returns cooled coolant from the base of the radiator to the engine,...

Chassis Mounting Plate is a spreader plate for the body mounting bracket, fitting at the chassis outrigger where the body is secured to the chassis...

Corner Bracket - Galvanised - LH on the rear body panel at the tailgate aperture. This galvanised steel bracket is fitted to the body on the left-...

Hood Grab Handle for the soft top assembly. The handle is fitted to the soft top to provide a hand grip for occupants. It mounts to the hood frame...

Steering Column Top Clamp in the steering column mounting, securing the upper end of the steering column to its support bracket. The clamp holds t...

Blade Wiper

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Grommet is a sealing grommet fitted to the engine oil sump on V8 petrol engines. It seals the point where a tube or fitting passes through the sum...

Injector Spill Pipe links the fuel injectors in the 2.5L 4-cylinder turbo diesel injection system. It returns leak-off (spill) fuel from the injec...

Plenum Hose is a moulded hose serving the plenum chamber of the V8 EFI petrol induction system. It forms part of the plenum chamber assembly on th...

Door Latch Stud Plate for the front door latch mechanism. The striker stud plate mounts to the body pillar and provides the fixed engagement point...

Tailgate Transfer Decal - "TDi" Badge for the Discovery 1 body graphics assembly. This self-adhesive transfer decal carries the "TDi" engine desig...

Decal - TDi - a self-adhesive "TDi" engine decal for the front wing, in light grey and measuring 9cm. The decal reproduces the original "TDi" wing...

Bush - Low Gear Wheel is a gearbox internal bush fitted to the low gear wheel in the Series 2 and Series 3 manual gearbox on 109-inch 1-ton Land Ro...

Rear Window Sealing Pad for the Range Rover Classic. This rubber pad seals the rear side window aperture, preventing water ingress and wind noise ...

Top cover

Accelerator Cable for the throttle control linkage, connecting the accelerator pedal to the engine's throttle mechanism. The cable transmits pedal...

Sill Panel - LH for the Defender 110 Station Wagon and Crew Cab body variants, forming the exterior body panel along the left-hand lower sill line ...

Speedometer Cable for the Discovery 1 instrument drive circuit. This mechanical drive cable connects the gearbox or transfer box output to the spe...

Front Name Plate – moulded plastic exterior badge fitted to the front of the vehicle. This is the decorative name plate that mounts to the front b...