Land Rover Parts

Name Plate is a moulded plastic exterior badge fitted to the body panel.

Exhaust Rubber Mount (insulator) that suspends the exhaust system from the underbody. The flexible rubber isolates exhaust vibration and noise from...

Front Lower Engine Mounting is the lower insulator supporting the engine at the front of the mounting system. It locates the engine to the subfram...

Upper Knuckle Bolt is a hex-head bolt that retains the upper knuckle joint within the hub and knuckle assembly. It clamps the upper knuckle to the...

Ride Height Sensor for the rear axle, part of the electronic air suspension system. The sensor links the vehicle body to the rear suspension arm a...

Ride Height Sensor for the front of the electronic air suspension system. It measures the position of the front suspension arm relative to the body...

Exhaust Gas Temperature Sensor for the diesel particulate filter (DPF) system. Monitors exhaust gas temperature in the after-treatment section and...

Wire Assembly

EGR Gasket Inlet

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Vacuum Hose for the brake servo (booster) vacuum supply circuit, connecting the engine vacuum pump to the servo inlet. On diesel applications the ...

Suspension Arm Bush for the front upper suspension arm, part of the front suspension arm and anti-roll bar assembly. The shouldered bush is presse...

Brake Disc - Solid - Rear is a solid (non-vented) disc forming the friction surface of the rear disc brake assembly. The disc mounts to the rear h...

Brake Servo Vacuum Hose connecting the engine vacuum pump to the brake servo, within the master cylinder and servo assembly. It carries the vacuum ...

Rear timing belt kit - fuel injection pump drive for the 3.0L V6 turbo diesel engine. The rear belt drives the high-pressure fuel injection pump a...

Rear Door Wiring Harness - the door-side section of the body electrical system, passing through the door pillar grommet into the rear side door. T...

Brake Disc - front axle, internally vented. The disc provides the friction surface that the front brake pads clamp against, converting the vehicle...

Trim Clip, male half, used in the facia and dash trim assembly. The clip is the male part of a two-piece push-fit fastener. It locates in the trim...

Idler Pulley for the front auxiliary drive belt on the 2.7 and 3.0 V6 diesel engines, part of the pulleys and drive belts assembly at the front of ...

Brake master cylinder for vehicles fitted with the four-wheel anti-lock braking system. It sits in the brake hydraulic circuit between the brake se...

Engine Cover - 2.4 Diesel

Camshaft Cover for the Puma 2.4L TDCi diesel engine. This cover encloses the top of the cylinder head, housing and protecting the camshaft and valv...

Transmission Oil Pan - fluid pan for the ZF 6HP26 / 6HP28 six-speed automatic transmission, forming the base of the transmission casing and holding...

Exhaust Manifold Gasket - sealing gasket for the exhaust manifold of the 2.4L Duratorq-TDCi HPCR diesel engine. It seals the joint between the exh...

Oil Cooler Return Connector is a connector fitting in the engine oil cooler circuit of the 2.2L diesel engine (DW12). It joins the oil cooler retu...

Fuel Pipe - the pipe run to the fuel pump within the fuel supply lines. Forms part of the low-pressure fuel delivery circuit, carrying fuel to the...

Oil Filter Housing Cover for the oil cooler and filter housing on the 2.2L DW12 turbo-diesel engine. The cover closes the oil filter housing, reta...

Flange Bolt that secures the rear output drive flange to the transfer box output shaft. It clamps the propshaft drive flange onto the transfer box...

Fuel Injection Pump Bolt secures the high-pressure fuel injection pump to its mounting on the engine. It provides the clamping load that holds the...

O-Ring Seal for the fuel injectors on the 2.4L Duratorq TDCi (Puma) diesel engine. Seals the fuel injector within the injection system to prevent ...

Injector Pipe No 4 is a high-pressure fuel pipe in the common-rail injection system of the 2.4L Duratorq TDCi (Puma) diesel engine. It carries fue...

Injector Pipe No 3 is a high-pressure fuel pipe in the common-rail injection system of the 2.4L Duratorq TDCi (Puma) diesel engine. It carries fue...

Injector Pipe No 2 is a high-pressure fuel pipe in the common-rail injection system of the 2.4L Duratorq TDCi (Puma) diesel engine. It carries fue...

Injector Pipe is the number-one high-pressure fuel line, carrying fuel from the common rail to the first injector on the 2.4L Duratorq-TDCi HPCR tu...

Vacuum Pump Mounting Gasket seals the joint between the engine-driven vacuum pump and its mounting face on the cylinder head. It maintains the air...

Water Outlet Connection for the 3.6L V8 TdV8 diesel engine cooling system, mounted at the thermostat housing. It carries engine coolant from the c...

Inlet Manifold Air Duct - routes charge air into the inlet manifold as part of the engine air intake, carrying incoming air from the intake system ...

Fuel Injection Pump Gasket for the 3.6L V8 diesel engine (TdV8), sealing the high-pressure fuel injection pump to its mounting on the engine. It f...

Nut for the diesel fuel injection pump and timing gear. Secures the drive gear to the high-pressure fuel injection pump on the 2.7L Lion V6 diesel...

Rear suspension bump stop - part of the rear damper and coil spring assembly. The moulded rubber bump stop fits over the shock absorber piston rod...

Crankshaft Position Sensor - engine management sensor located at the crankshaft, reading a toothed reluctor ring driven by the crankshaft. The sen...

Crankcase Breather Hose for the 2.5L KV6 petrol engine, part of the crankcase ventilation system. It carries blow-by gases from the cylinder head ...

Breather Hose connecting the camshaft cover breather outlet to the inlet manifold on the 2.5L KV6 petrol engine. Part of the crankcase ventilation...

Front Camshaft Oil Seal for the Td5 2.5L 5-Cylinder Turbo Diesel engine, fitted at the timing end of the camshaft within the cylinder head. Seated...

Heat Shield - Engine Mount for the Puma diesel engine mounting assembly. This shield mounts over the engine mount rubber to protect it from heat a...

A/C Compressor O-Ring seals a refrigerant line union at the air conditioning compressor. The O-ring is clamped between the pipe end fitting and th...

Clip retains the heater and air-conditioning control cable within the HVAC control assembly, holding the cable on its correct routing.

Trim Clip retains interior trim panels against the body. The clip pushes into a pre-formed aperture in the body panel and holds the trim in place ...