for Discounts / VAT
for Discounts & Correct VAT
Browse our complete range of Land Rover and Range Rover parts- from OEM-quality replacements to specialist upgrades. Whether you’re restoring a classic Defender, maintaining a Discovery, or tuning a modern Range Rover, our parts selection covers every system: engine, suspension, braking, transmission, and more.
Gearchange Roll Pin - a tension (roll) pin used in the manual gearchange mechanism to secure the gear lever to the selector shaft. Applies to the ...
View full detailsExhaust U-Bolt secures a joint in the front section of the exhaust system. The U-bolt clamps over the pipe at a slip joint and, tightened against i...
View full detailsBonnet Stop Buffer is a rubber buffer that cushions the bonnet where it rests against the body when closed. Mounted on the front bodywork, it supp...
View full detailsCylinder Head Dowel - Plastic is a locating pin fitted at the mating face between the cylinder block and cylinder head in the Td5 2.5L 5-cylinder t...
View full detailsA/C O-Ring - a sealing O-ring for the air conditioning refrigerant hose connections. It seats at the couplings between refrigerant hoses and compo...
View full detailsFastener used to secure interior door casing panels and body side trim. Retains door casing and rear body panel trim on applicable vehicles.
Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...
View full detailsLocking Wheel Nut Cover for alloy road wheels on the Freelander 1. Plastic protective cap that fits over locking wheel nuts on alloy wheels, cover...
View full detailsBrake pipe clip
Manifold Stud - a mounting stud that secures the exhaust manifold to the cylinder head. It threads into the cylinder-head casting and projects thr...
View full detailsBump Stop for the suspension, mounted at the limit of axle travel. This rubber stop caps upward suspension movement at full compression, providing...
View full detailsPTO Selector Cover Plate - a blanking plate for the power take-off (PTO) selector aperture on the transfer box. It covers and seals the selector o...
View full detailsstrip BTR919PUB
Engine & Gearbox Mount - Lower The lower (bottom) rubber mounting that isolates the engine and gearbox from the chassis, absorbing running vibr...
View full detailsQuarter Window Catch is the latching assembly for the side-opening rear quarter window, in the Lunar colour finish. Mounted to the hinged quarter ...
View full detailsCaliper Seal - Rear
Heater Controls Spacer - spacer fitted within the heater control assembly of the HVAC unit. Sold individually.
Handbrake Gaiter for the handbrake lever assembly in Series II, IIA, and III Land Rovers. Fits 109-inch wheelbase V8-engined variants. The gaiter ...
View full detailsDial Illumination Bulb - the backlight bulb and bulbholder assembly for the LCD climate control panel, part of the heating and ventilation controls...
View full detailsClevis pin
Door Handle Cap - LH is the left-hand end cap for the exterior front door handle assembly, incorporating the lock barrel aperture. The cap forms t...
View full detailsRetaining Clip for the front door lock, also known as the door lock plate.
Heater Control Pin
Accelerator Rod in the throttle linkage. This rigid rod transmits accelerator pedal movement through the linkage to operate the engine throttle.
Filler Strip is the fixing channel that runs along the top edge of the rear door window aperture. It locates and retains the upper edge of the doo...
View full detailsEngine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...
View full detailsHose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...
View full detailsRotor Arm for the 24V shielded ignition distributor. The rotor arm mounts on the top of the distributor shaft and, as it rotates, routes the high-t...
View full detailsAir Cleaner Ring for the Range Rover L322 intake assembly. This sealing ring fits within the air cleaner housing on the BMW M62 B44 4.4-litre V8 p...
View full detailsExhaust Bracket for the exhaust mounting system. This bracket supports the exhaust line at the section immediately behind the front silencer, loca...
View full detailsAccelerator Cable for the Range Rover Classic 3.5L V8 carburettor engine, left-hand drive, manual transmission. This cable connects the accelerato...
View full detailsCylinder Liner - the replaceable liner that forms the bore in which the piston and rings run within the cylinder block. It provides the hard weari...
View full detailsPlenum Hose is a moulded hose serving the plenum chamber of the V8 EFI petrol induction system. It forms part of the plenum chamber assembly on th...
View full detailsFiller and Level Plug for the V8 4-speed gearbox and for differential assemblies across a wide range of classic Land Rover models. Fitted at the s...
View full detailsThermostat regulates coolant flow within the engine cooling circuit of the 2.5L 4-cylinder VM Turbo Diesel. Housed in the thermostat housing at th...
View full detailsDecal is an exterior body decal applied to the rear of the vehicle. It carries the Land Rover name in silver lettering on a black background, and ...
View full detailsRear Side Door Channel is a glass run channel mounted within the rear side door, fitted to the right-hand (RH) side. The channel locates and guide...
View full detailsRear Fog Switch for the dashboard switching circuit. A push-push type switch that controls activation of the rear fog lamp circuit. Mounts in the ...
View full detailsDistance piece
Bonnet Decal - Silver - self-adhesive exterior decal applied to the bonnet, finished in silver.
ROVER Lettering Emblem - silver, 35 cm - for Defender (2007-2016). This is the adhesive silver lettering strip that spells out "ROVER" on the exte...
View full detailsEmblem - LAND - Silver - 28cm is the "LAND" lettering badge that forms part of the bonnet exterior script. The silver badge measures 28 cm in leng...
View full detailsHeater Bypass Coolant Valve for V8 petrol applications. This vacuum-operated valve is installed in the HVAC coolant circuit and controls the flow ...
View full detailsCab Mounting Stud
Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...
View full detailsSteering Hose forms part of the power steering hydraulic circuit. It carries pressurised hydraulic fluid between the power steering pump and the s...
View full detailsBonnet Latch Assembly for vehicles equipped with the anti-theft alarm system. This latch secures the bonnet in the closed position and incorporates...
View full detailsDoor Stay for the luggage compartment (lower tailgate) door. Restrains the door's opening travel and supports it in the open position, taking the l...
View full detailsThis page lists every Land Rover and Range Rover part stocked across our Dutch warehouse network. With the full catalogue in one place, the fastest way to reach the right component is to narrow down by your model or by the system you are working on, using the links below.
Shop by modelParts for Series-derived, Td5, Puma and L663 Defender generations.
Land Rover Defender partsParts spanning Discovery 1 through Discovery 5 and Discovery Sport.
Land Rover Discovery partsParts for every Range Rover line from Classic to the latest generations.
Range Rover partsParts for Freelander 1 and Freelander 2 across petrol and diesel variants.
Land Rover Freelander partsPanels, mounts, fasteners and structural components.
Land Rover chassis and body parts