Land Rover Parts

Wiper Drive Tube is part of the windscreen wiper drive mechanism, guiding the drive between the wiper motor and the wheelboxes. It houses the flex...

Coolant Temperature Sensor - screws into the thermostat housing as part of the engine cooling system. It senses coolant temperature in the thermos...

Alternator Belt for the TD6 2.9L inline-six turbo diesel engine. It forms part of the auxiliary drive (accessory belt) system, transferring rotatio...

Exhaust Downpipe Bracket for the front section of the exhaust system. Locates and supports the front exhaust downpipe against the engine/chassis, ...

Exhaust Clamp securing a front exhaust pipe joint. This clamp draws together and seals the joint between two sections of the front exhaust, holdin...

Anti-Roll Bar Bracket - Rear secures the rear anti-roll bar to the chassis, forming part of the rear stabiliser bar mounting. The bracket clamps o...

Exhaust Clamp - Angle An angled clamp in the exhaust system, fitted at the rear of the twin-pipe arrangement. It secures the exhaust pipe to its m...

Door Hinge mounts a side door to its body pillar, forming part of the door hinge assembly. The hinge carries the weight of the door and sets its a...

Glow Plug is a heating element threaded into the cylinder head of the 2.2L CR DI diesel engine, forming part of the pre-heating system. One plug s...

Windscreen Washer Jet is a heated spray nozzle in the windscreen washer system. Mounted on the scuttle, it receives pressurised washer fluid from ...

Front Anti-Roll Bar Bush for the front stabiliser (anti-roll) bar. The bush locates the anti-roll bar to its mounting, permitting controlled rotat...

Gearshift Lever Seal seals the base of the gear lever where it enters the manual gearbox housing. It prevents oil loss from the gearbox and keeps ...

Function Multi Wire

Turbocharger Gasket for the left-hand turbocharger on the 3.6L V8 diesel (Lion) engine. It seals the mounting joint between the turbocharger and i...

Glow Plug for the 2.2L Td4 diesel engine. Fitted to the cylinder head, it pre-heats the combustion chamber to aid cold starting and is controlled ...

Inlet Manifold Gasket (Front) for the 4.4L M62 V8 petrol engine, sealing the front section of the inlet manifold against the cylinder head. It mai...

Differential Bearing Shim for the axle differential assembly. The shim fits behind a differential carrier bearing in the axle casing. It sets the ...

Mainshaft 3rd Gear Bush - LT77 is the bearing bush for 3rd gear on the mainshaft of the LT77 5-speed manual gearbox. It sits between the mainshaft...

Clutch Release Pivot for the clutch release mechanism, mounted inside the bellhousing. The pivot provides the fulcrum on which the clutch release ...

Grommet - moulded rubber grommet for a panel or component aperture. Fitted into a drilled or pressed hole to line the opening, it provides a seal ...

Gas Strut for the upper tailgate glass window. This gas-filled strut supports the opening rear glass of the tailgate, damping its travel and holdi...

Tilt Stud for the soft top (tilt) and hood frame fixing. Mounts to the body to receive the retaining plate that secures the canopy tilt to the veh...

Differential Pinion Shim - 0.052in. Fitted between the pinion head and its bearing to set pinion depth and preload during differential setup. Shim...

Mainshaft Thrust Washer for the Series I and Series II gearbox assembly. This 0.135 in (135 thou) washer controls the axial location of 3rd gear o...

Banjo Washer for the oil feed pipe banjo union at the turbocharger, used on TDV6 2.7L/3.0L and TDV8 3.6L/4.4L diesel engines. This sealing washer ...

Handbrake Cable - left-hand cable in the parking brake system. This cable transmits the handbrake lever's travel to the rear brake actuating mecha...

Motor Pinion

Wiring Connector for the chassis wiring harness, used in the fuel tank circuitry. The connector forms a serviceable electrical junction between ha...