Land Rover Parts

Front Wing - LH

Rocker Shaft for the 2.6L six-cylinder petrol engine, part of the valvetrain in the cylinder head. The shaft mounts on the head and carries the ro...

Exterior Door Mirror - Electric, Right-Hand - door-mounted exterior mirror assembly for the right-hand side. The mirror head is electrically adjus...

Heater Hose forming part of the cabin heater coolant circuit, carrying feed coolant from the engine cooling system to the heater matrix. For the 2...

Washer Bottle - the washer fluid reservoir for the windscreen, rear screen and headlamp wash circuits. It stores the washer fluid and carries the ...

Rear Mudflap Bracket for the Range Rover Classic body. This bracket mounts to the rear bodywork to carry the rear mudflap, positioning it correctl...

Handbrake Shoe Kit - the retention (hold-down) hardware for the transmission handbrake, which acts on the LT230 transfer box rather than at the roa...

Thrust Washer for the LT95 four-speed gearbox, 3.75mm thickness. This selective-thickness washer sets the end-float of the intermediate gear.

Hi/Lo Range Gear is a range gear within the LT230 transfer box. The transfer box splits drive from the gearbox to the front and rear axles and pro...

Seat Back Foam Pad is the foam cushion for the front seat backrest. Fitted over the seat frame and beneath the seat cover, it provides the backres...

Exhaust Mounting U-Bolt used to clamp and secure the exhaust system to its mounting bracket on the Range Rover Classic. This U-bolt wraps around t...

Piston Ring Set seals the piston within the cylinder bore as part of the engine's piston assembly, providing combustion sealing, oil control and he...

Inlet Manifold forms part of the engine air intake system, distributing the intake charge to the cylinder head inlet ports. Fitted to the 2.5-litr...

Y Piece

Active Cornering Enhancement (ACE) Pump for the Discovery 2. This hydraulic pump is the primary pressure source within the ACE system, which activ...

Retainer - LH

Throttle Cable Bracket within the carburettor throttle control. Anchors the outer throttle cable, providing a fixed abutment so the inner cable ca...

scew hexagonal head M6 x 45mm 4-speed LT95 and 5-speed gearbox bottom cover plate (with Rover V8 engine)

Plastic Clip for the radiator and fan cowl assembly. The clip locates the cowl to the radiator and retains the surrounding cooling system trim, ho...

Oil Drain Plug Gasket for the transfer case drain plug. Sealing washer fitted between the drain plug and the transfer case to prevent oil leaks.

Bolt Set Screw 7/16UNC x 1.25" 2.25L diesel: startermotor to engine (Imperial, non-metric engines) 2.6L petrol: oil filter housing to adaptor

Headlamp mounting panel RH

Throttle Cable for the accelerator linkage of the VM diesel engine. The cable transmits accelerator pedal movement to the throttle lever on the fu...

Chassis Wiring Harness - Heated Rear Window & Rear Wiper is the rear body/chassis section of the wiring loom that supplies the heated rear wind...

Bonnet - Defender

Valance Panel

Column Switch

Starter Motor Drive Assembly is the pinion drive of the starter motor, used on V8 petrol engines fitted with the Bosch starter. When the starter i...

Filler Fuel

Gear Selector Kit for the manual gearbox, covering the internal gear-selection mechanism that engages and disengages the gear ratios. The selector...

Brake Adjuster sets and maintains the shoe-to-drum clearance within the rear drum brake assembly. It locates between the brake shoes and adjusts t...

Brake Adjuster Assembly sets and maintains the shoe-to-drum clearance within the rear drum brake assembly. It locates between the brake shoes and ...

Rear Upper Tailgate Handle, the exterior handle assembly for the upper section of the split rear tailgate. It provides the grip and release point ...

Brake Master Cylinder is the hydraulic actuator at the head of the braking system. Mounted to the face of the brake servo, it converts brake-pedal ...