Land Rover Parts

Oil Filter for Land Rover petrol and diesel engines, part of the engine lubrication circuit. This screw-on canister filter threads onto the filter...

Nyloc Nut with a 3/8" UNF thread, used to secure propshaft flange bolts. A nylon insert set into the crown of the nut deforms over the bolt thread...

Transfer Box Output Flange Oil Seal is a radial shaft seal fitted at the output flange of the LT230 transfer box, sealing between the rotating outp...

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Front cover oil seal

Hylomar Hylosil 100 is a neutral-curing RTV silicone sealant for gasketing, sealing and bonding in automotive and engineering applications. It cure...

Front Driveshaft Oil Seal located at the differential housing output in the Front Axle Assembly, sealing around the front halfshaft where it exits ...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Nyloc Nut with a 3/8" UNF thread and a 12 mm across-flats hex, in the full-height (thick) form. A nylon insert set into the crown of the nut defor...

Nyloc Nut with an M20 thread, used across suspension and driveline flange fastenings. A nylon insert set into the crown of the nut deforms over th...

Hylomar Universal Blue is a non-setting gasket jointing compound for use on gaskets and machined metal joint faces in automotive and engineering ap...

Inlet Manifold Gasket for the V8 petrol engine, forming the seal between the central inlet manifold casting and the cylinder head intake faces. It...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Oil Cooler Pipe O-Ring for engine and transmission oil cooling circuits. This O-ring seals pipe fitting and hose connection joints in the oil cool...

Air cleaner element installed in the engine intake air cleaner housing to filter incoming air before it reaches the induction system. The element...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Differential Taper Roller Bearing for the axle differential assembly. It supports the differential carrier within the axle casing, carrying the com...

Upper Ball Joint for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint; this upper ...

Rear Brake Pad Set for the rear disc brakes, supplied as an axle set covering both rear wheels. The friction pads are clamped against the rear bra...

Coolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Nyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...

Brake Disc Fixing Screw that secures the brake disc to the wheel hub. The screw locates and retains the disc against the hub face during assembly,...

Gear Knob - gear lever knob for the R380 5-speed manual gearbox. Threads onto the gearchange lever, forming the driver's hand grip and gear-select...

LT230 Intermediate Shaft O-Ring, sealing the intermediate shaft within the LT230 two-speed transfer box main casing. The intermediate shaft transm...

Nut - M6 is a plain M6 hexagonal nut used as a general-purpose threaded fastener throughout the chassis, body and mechanical assemblies. It tighte...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Slipper pad

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Interior Lamp Bulb is a 239-type festoon bulb rated 12V 5W with a C11 (SV8.5) double-ended cap, used in the interior lighting circuit. The bulb se...

Coolant - Blue RTU pre-mixed engine coolant and antifreeze for older Land Rover models. Ready to use straight from the container - no dilution req...

Oil Pressure Switch for the V8 petrol engine, forming part of the engine oil pressure warning circuit within the lubrication system. The switch th...

Lower Ball Joint - Front Hub for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint;...

Spark Plug Ignition component for the Rover V8 petrol engine. Threaded into the cylinder head, it carries the high-voltage current from the igniti...

Locking plate

Rocker Cover Gasket for the V8 petrol engine, cork construction. The gasket seals the joint between the rocker cover and the cylinder head, contai...

Pinion oil seal

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

screw M5 x 12

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...