Products

Bulb 24V 21/5W dual-filament bulb for 24-volt electrical systems. The 21W filament serves the stop light circuit and the 5W filament serves the tai...

Sediment Retainer for the fuel lift pump glass sediment bowl - the clamp that secures the glass bowl to the underside of the pump. It holds the bo...

Ball Joint - Accelerator Linkage is a mechanical pivot joint used in the accelerator linkage assembly. This ball joint connects articulating rods ...

Brake Drum Screw for the brake drum assembly. This retainer screw secures the brake drum to the wheel hub flange, preventing the drum from displac...

Braided Earth Strap with Battery Clamp - 300mm for the vehicle electrical grounding circuit. This braided copper earth strap is fitted with an int...

Braided Earth Strip is a flexible braided conductor that forms an electrical earth (ground) bond between two points in the vehicle. It provides a ...

Nut is a hexagonal nut cut with a 7/16" BSF (British Standard Fine) thread. It threads onto a matching 7/16" BSF bolt or stud to secure a bolted j...

Speedometer Pinion Oil Seal for the gearbox speedometer drive take-off. It seals around the speedometer drive pinion where it enters the gearbox ho...

Steering Relay Oil Seal for the steering relay unit, part of the steering linkage. The steering relay transfers movement from the steering box dro...

Exhaust Gasket sealing the exhaust manifold-to-downpipe flange on Series Land Rover 4-cylinder petrol and diesel engines. This four-hole flange ga...

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Track Rod End Boot Ring - spring retaining ring for the track rod end of the steering linkage. It clamps the rubber dust boot onto the track rod en...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Driving Member Bolt for the axle driving member assembly. This 3/8" BSF x 1-19/32" bolt retains the driving member to the hub assembly. The drivin...

Bolt with Whitworth (BSW) thread - 1/4 inch diameter, 1-1/4 inch length, sold individually. Used across Series Land Rover applications requiring t...

Clevis Pin - pivot pin used in the mechanical brake and transmission linkages. It passes through a forked clevis and the eye of a mating rod or lev...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Double-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Wheel Nut for the road wheel and hub assembly, securing the road wheel onto the hub studs. The double-chamfer design is tapered at both ends, so t...

Oil seal

Axle casing oil seal

Gear Change Selector Shaft Spring A spring for the gearbox gear-change selector mechanism. It acts on the selector shaft to provide the spring loa...

Mainshaft Nut for the LT76 gearbox, fitted to the mainshaft and gear assembly. It retains the gear cluster on the mainshaft, clamping the stack ag...

Pinion Bearing Retaining Plate for the Power Take-Off (PTO) unit on Series Land Rovers. This retaining plate locates and secures the pinion bearin...

Circlip - Rear Mainshaft Bearing for the Series Land Rover gearbox. This circlip retains the rear mainshaft bearing within the gearbox casing, pre...

Bolt for the LT76 gearbox assembly, with a 5/16" BSF (British Standard Fine) thread. Used as a threaded fastener within the gearbox casing.

PTO Selector Cover Plate - a blanking plate for the power take-off (PTO) selector aperture on the transfer box. It covers and seals the selector o...

Handbrake Stud A mounting stud for the transmission (drum) handbrake within the braking system. It secures the transmission brake back plate to th...

Transfer Box Mainshaft is the central rotating shaft within the transfer box assembly, running through the gear train and transmitting drive betwee...

Starting Handle for manual cranking of the engine. The handle engages the dog on the front of the crankshaft, allowing the crankshaft to be turned...

Drive Shaft Hub Cap for the hub assembly on Land Rover Series vehicles. This cap fits at the outer face of the hub, closing off the drive shaft en...

Transfer Case Intermediate Gear with a 44/22 tooth configuration, operating within the transfer box gear train. The intermediate gear meshes with ...

Transfer Lever Knob in red, for the high/low range selector on the transfer gearbox. It threads onto the top of the transfer change lever and prov...

Inner Pinion Bearing for the Land Rover Series axle differential, supporting the pinion shaft at the inboard (crown wheel) end within the different...

Gear Lever Housing The ball/socket housing for the main gear lever, mounted on the gearbox top cover (turret). It seats the spherical lower end of...

Gear Lever Retaining Spring The spring that retains the main gear lever in its ball housing on the gearbox top cover. It bears down on the lever's...

Circlip - Gear Lever Spring Retention for the Series Land Rover gearbox gear lever assembly. This circlip retains the spring, retaining plate and ...

Flexible Brake Hose - hydraulic hose carrying brake fluid from the rigid chassis or axle pipe to the wheel cylinder. Forms the flexible link acros...

Four-Wheel Drive Selector Lever Bush for the transfer box gearchange linkage. The bush locates the four-wheel-drive selector lever at its pivot, t...

Joint Washer for the transfer gearbox top cover. This gasket seals the joint between the top cover and the transfer box housing, preventing oil le...

Swivel Pin Seat Cone for the front axle swivel housing. This cone provides the precision seating surface on which the swivel pin locates within th...

Gearbox Reverse Stop Spring for the gear selector mechanism. The spring acts on the reverse stop plunger, providing the resistance the gear lever ...