Products

Bulkhead Top Corner Repair - LH

Bulkhead Top Corner Repair - RH

Restore your Series or Defender Land Rover's door with this door bottom repair section. This replacement piece is designed to repair damaged or rus...

Standard seat set covering the full front seat row of a Series cab – both outer seats and the centre seat. The set consists of six pieces: two out...

Bulkhead Repair Panel with Vents - Left-Hand is a weld-in repair section for the upper corner of the bulkhead, incorporating the fresh-air vent sur...

Bulkhead Repair Panel with Vents - Right-Hand is a weld-in repair section for the upper corner of the bulkhead, incorporating the fresh-air vent su...

Brake Kit - Series - SWB - To June 1980

Wind Deflector Set - a pair of stick-on air deflectors for the front door windows. Each deflector fits to the outer edge of the door window frame ...

Headlamp Surround — the chrome bezel that trims and retains the outer edge of a 7-inch round headlamp. A polished chrome ring fitted over the head...

7 Inch Round LED Headlamp for the front lighting system, replacing the conventional 7-inch round sealed-beam or halogen headlamp. The LED light so...

Seat Box Corner Protector - Pair - Black Steel

Heater Plug - Single Plug - 2.25 Petrol

Steering Wheel Boss in the steering column assembly, providing the mounting interface between the column shaft and the steering wheel. The 48-spli...

Upgrade your Land Rover Defender (1987-2006, 2007-2016) or Series 3 with the WIPAC LED 73mm smoked lamp kit. Smoked LED style light for a sleek...

Static Lap Seat Belt for the second-row seating position, forming part of the interior occupant restraint system. The non-retractable, fixed-lengt...

Static Lap Belt - a two-point lap seat belt for a centre or side-facing seating position. The webbing is a fixed length and is adjusted by hand to...

Transfer Box Gear Set - High Ratio is a gear set for the two-speed transfer box that raises the high-range gearing. By raising the high-range rati...

bushes needed to machine the Series LT76 transfer case for the High Ratio Gear Set (HGRS.)

Brake Pipe Union for the hydraulic brake system, a female fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic ci...

Rubber isolator clamp used in the bonnet-mounted jack bracket assembly to secure the jack beam or handle against the bonnet mounting brackets. The...

7" round LED headlamp 12/24V black 78W LHD (pair)

7" round LED headlamp 12/24V chrome 78W LHD (pair)

7 inch high low beam headlight LHD black, with U shape parking light, (PAIR)

Portable Jump Starter and Air Compressor - a handheld 12V power pack combining a battery jump starter, power bank, tyre inflator and LED work light...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Crown Wheel & Pinion Set - the final-drive gear pair housed within the axle differential. The pinion takes drive from the propshaft and turns t...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Dynamo to Alternator Conversion

T-Piece Hose Connector is a three-way junction fitting used in a flexible hose run. It joins three hose ends at a single point, allowing a hose li...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Manifold Absolute Pressure (MAP) Sensor, part of the engine management system. The MAP sensor measures the absolute pressure inside the intake man...

Door Checker Bracket Assembly - Rear - LH is the door check mechanism for the left-hand rear door. It links the door to the body pillar and limits...

Bonnet Buffer is a resilient rubber cushion that forms part of the bonnet closure assembly at the front of the body. It provides the stop the bonn...

Seat Base - Outer is the lower seat cushion for either outer (driver or passenger) position in the front seating assembly. Foam-padded and finishe...

Seat Back for the outer front seat, in the deluxe pattern and finished in black. This is the upholstered backrest (squab) the occupant leans agains...

Seat Back and Headrest for the outer front seat, in the deluxe pattern and finished in black. This is the upholstered backrest (squab) the occupant...

Glass

Sending is only possible by pallet. Too fragile for normal parcel delivery.

Doortop Unglazed - Series - RH