Products

Front left-hand wheel cylinder for the hydraulic front braking system, installed within the brake backplate assembly of 11-inch front brake configu...

Wheel brake cylinder LH

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Outer Distance Piece for the front axle swivel pin housing. The distance piece is a spacer that sets the position of the swivel pin bearing within...

Exhaust Connecting Pipe is the intermediate section of the exhaust system for Series short wheelbase vehicles fitted with the 2.25L diesel engine, ...

Oil Pump Lock Tab, part of the engine oil pump assembly. The lock tab is a tab washer fitted under the oil pump retaining fastener; once the faste...

Main Starter Spring is the principal return spring within the starter motor assembly used on Series I, II, IIA, and III vehicles. It operates withi...

Gear - 2nd - Pair for the Series Land Rover four-speed main gearbox. This pair comprises the matched 2nd speed gears for both the mainshaft and th...

Flywheel Housing O-Ring - a sealing ring at the rear of the engine where the flywheel housing meets the cylinder block. Fitted to the 2.25L engine...

Cylinder Head Bolt - a clamping bolt securing the cylinder head to the engine block. It draws the head down onto the block to compress the head ga...

Camshaft Cover Gasket seals the camshaft cover plate to the cylinder block, forming part of the camshaft housing and engine lubrication boundary. ...

Set Screw - Water Pump Spindle is a locking fastener that locates the water pump spindle within the water pump housing on Series engines produced b...

Domed Nut with a 5/16 UNF thread, a finishing fastener. The domed (acorn) form encloses the end of the stud or bolt it threads onto, protecting th...

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...

Manifold Stud - a mounting stud for the manifold. Threaded into the cylinder head, it locates the manifold and clamps it to the head face via its ...

Valve Stem Oil Seal fits over the inlet valve stems to limit oil consumption past the valve guides in the cylinder head. It is used on 2.25L petrol...

Banjo Bolt for the timing chain tensioner hydraulic oil feed on Land Rover 2¼ Litre and 2.0 Litre diesel engines. The banjo bolt is a hollow faste...

Rocker Cover Stud for the cylinder head on early Land Rover 4-cylinder engines. The rocker cover stud is a threaded fastener installed into the cy...

Lock Washer secures a threaded fastener against loosening under vibration and thermal cycling. Fitted beneath the nut or bolt head, it bites into ...

Inlet Rocker Bush for the valve gear, forming the bearing surface between the inlet rocker arm and the rocker shaft. The bush locates the inlet ro...

Water Pump Impeller in the engine cooling circuit. Pressed onto the water pump spindle and driven by the fan belt, the impeller circulates coolant...

Heater Plug Lead in the diesel glow plug pre-heat circuit. This 10" interconnecting lead links the No.2 and No.3 heater (glow) plugs, carrying cur...

Glow Plug Lead in the diesel glow plug (heater plug) pre-heat circuit. This short 5" lead interconnects glow plugs wired in series and is not inte...

Wing Nut with a 1/4" BSF thread, tightened by hand without tools. Used to secure the battery clamp frame and the oil-bath air cleaner clamp, where...

Bolt securing the gearbox to the transfer box in the drivetrain. This fixing clamps the main gearbox housing to the transfer box. It applies to th...

Lock nut 3/8" BSF

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Bolt - 1/2 UNF x 1 is a hexagon-head set bolt in 1/2 UNF (Unified National Fine) thread, 1 inch in length, used to secure the engine mounting brack...

Steering Rocker Shaft Bush - a bearing bush within the steering relay assembly. The bush locates and supports the rocker (relay) shaft inside the ...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Sealing Ring A rubber O-ring sealing ring serving two separate shaft and tube interfaces. It is used on the transfer box high/low range selector s...

Wheel Cylinder Overhaul Kit for front drum brake systems fitted with 11-inch brake drums. This kit provides the necessary parts to overhaul all fo...

Wheel Cylinder Repair Kit A seal repair kit for overhauling the rear brake wheel cylinders, part of the drum braking system. The wheel cylinder si...

Mainshaft Thrust Washer - 2nd Gear (0.125") is a selective shim located within the Series gearbox, fitted to control axial play on the second gear ...

Thrust Washer for the 2nd gear assembly within the manual gearbox. Fitted to the mainshaft to control the end float of 2nd gear, the washer is sel...

Rocker Cover Gasket (Exhaust Side) - seals the exhaust-side rocker cover joint on the 2.0L IOE (inlet-over-exhaust) engine. Fitted between the roc...

Rocker Cover Gasket sealing the inlet rocker cover to the cylinder head on the 2.0L petrol IOE (Inlet Over Exhaust) engine. Fitted between the upp...

Rocker Cover Gasket sealing the inlet rocker cover to the cylinder head on the 2.0L petrol IOE (Inlet Over Exhaust) engine. Fitted between the upp...

Sealing ring

Radiator Top Hose forms part of the engine cooling circuit, connecting the top tank of the radiator to the coolant outlet at the cylinder head. Th...

Brake Lining - Rear is a replacement friction lining for the rear drum brake assembly on long-wheelbase Land Rover models, covering 109-inch, 110-i...