Products

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Sill Panel (5" Deep, Front, Right-Hand) is the lower body panel that runs along the right-hand front body side beneath the door aperture. It forms...

Sill Panel (5" Deep, Front, Left-Hand) is the lower body panel that runs along the left-hand front body side beneath the door aperture. It forms t...

Tailgate Chain Cover - a pair of protective sleeves that fit over the two retaining chains supporting the rear tailgate. Each chain links the tail...

Hood Stick Kit - the framework of bows and sticks that forms the skeleton of a canvas soft top (tilt), carrying and tensioning the fabric over the ...

Tailgate Hook for the lower hinged tailboard, right-hand side. This pigtail (spiral) hook mounts on the body and retains the tailgate support stra...

Tailgate Hook for the lower hinged tailboard, left-hand side. This pigtail (spiral) hook mounts on the body and retains the tailboard chain, holdi...

Floor Mounting Pad is a 5mm rubber spacer pad used at the rear body floor support mounting, fitted between the body and the chassis-mounted support...

Turnbuckle is the semi-circular catch that fastens the seat box and rear tub locker lids down. It rotates over the mating hasp to hold the lid shu...

Bonnet Spring Retaining Clip, part of the bonnet hinge and stay assembly. Retains the bonnet (hood) tension spring against its anchor, holding the...

Transfer Gear Lever Gaiter for the high/low ratio selector lever on the Series Land Rover transfer box. This rubber gaiter seals around the transf...

Interior Mirror for Series Land Rover models. Direct-fit interior rear-view mirror providing rearward visibility from the driver's position inside...

Door Check Arm Bracket is the pivot bracket in the door check assembly that anchors the check arm to the body at the rear door. The check arm runs...

Window Channel - Vertical - the upright glass run for the Truck Cab side window, part of the door glazing assembly. It lines the vertical edge of ...

Window Channel - Top is the upper glass-run channel that guides the top edge of the window glass, supplied as a 94 cm length. It forms the running...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Bullet Connector, single-sleeve, one-way. Accepts a standard bullet terminal and is used throughout Land Rover wiring harnesses for individual wire...

Selector Detent Spring is part of the gearbox gear-selection detent for the forward-gear selector shafts (1st/2nd and 3rd/4th). It loads the deten...

Flywheel Housing Stud secures the flywheel housing to the rear of the cylinder block on the 2.0L petrol engine. The stud provides a threaded fixin...

Steel Ball for the timing chain tensioner, 7/32 in diameter. Seats within the tensioner mechanism to help maintain correct timing chain tension.

Plain Washer with a 1/4" bore, used as a general-purpose flat washer. Fitted under a bolt head or nut, it spreads the clamping load over a wider a...

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Front Door Check Strap, part of the front door hinge and retention hardware. Connecting the front door to the body pillar, the check strap limits ...

Plain Washer A flat plain washer that spreads the clamping load of a fastener over the mounting surface. Used in body panel and interior fixings.

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Engine & Gearbox Mount - Lower The lower (bottom) rubber mounting that isolates the engine and gearbox from the chassis, absorbing running vibr...

Shim plate

Layshaft First Gear - the first-speed gear on the layshaft (countershaft) of the main gearbox. Meshes with the corresponding mainshaft gear to pro...

Mainshaft Gear - 1st Speed is a 29-tooth first-speed gear that runs on the mainshaft within the manual gearbox gear train. As a non-synchronised c...

Locating Dowel for the flywheel-to-crankshaft joint, part of the crankshaft and flywheel assembly. Pressed into the crankshaft rear flange, the do...

Reverse Gate Bracket is the fixed section of the reverse-gate stop within the gear-lever mounting on the Series four-speed gearbox. It forms the g...

Handbrake Catch Pawl, the ratchet claw of the transmission parking brake mechanism. It engages the toothed quadrant on the handbrake lever, lockin...

In/out member spring

Headlamp bulb 12V 40/45W duplo (non-halogen)

Self-Locking Nut, 3/8" BSF, used to secure propshaft fasteners within the drivetrain. The deformed thread form provides a self-locking action that...

Plain Nut for use as a standard fastener across Land Rover applications. A plain (non-locking) hex nut for general assembly and repair work.

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

Flywheel Ring Gear for four-cylinder petrol engines. The ring gear is shrink-fitted to the periphery of the flywheel and meshes with the starter mo...

Thrust Washer for the gearbox mainshaft, 0.128" thick. This is a selective-thickness thrust washer used to set mainshaft end-float during gearbox ...

Thrust Washer - Mainshaft - 0.130 Inch is a gearbox internal component positioned at the 3rd gear location on the mainshaft in the Series 1, Series...

Gear Lever Locating Pin locates and retains the main gear lever within the manual gearbox. It holds the lever against its pivot so that shift move...

Tappet kit