Products

Wheel Stud, screw-in type, 9/16 BSF and threaded at both ends, fitting the front and rear axle hubs. The stud screws into the hub at one end; the ...

Clutch Withdrawal Tube fitted in the clutch cross-shaft withdrawal mechanism on Series II, IIA, and III Land Rovers. This tube forms the connectin...

Exhaust Silencer for right-hand-drive applications. Part of the exhaust system, this silencer attenuates combustion noise as the gases pass throug...

Exhaust Silencer for right-hand-drive applications, constructed in stainless steel. Part of the exhaust system, this silencer attenuates combustio...

Drop Plate Strengthener for the towing equipment assembly. It acts as a spacer and strengthener for the towing jaw and the towing jaw/ball fixings...

Front Exhaust Pipe forms the front section of the exhaust system, mounting to the exhaust manifold by a four-stud flange. It carries exhaust gas f...

Exterior Mirror - Round Arm is a complete wing mirror assembly comprising a round convex mirror head and a standard-length mounting arm, designed f...

Front Bumper in galvanised steel, mounting across the front of the chassis frame. It bolts to the front chassis dumb-irons to provide front-end im...

Shock Absorber Bush (sleeve type) fitted at the shock absorber mounting points in the suspension system. This rubber sleeve bush locates within th...

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

Radiator Drain Plug seals the drain point in the cooling system and is removed to drain coolant during flushing or servicing. When fitted it close...

Bulb rated 12V 4W with a small-diameter fitting, part of the vehicle lighting system. This low-wattage bulb suits the small-fitting (Lucas-type) l...

Bronze Distance Piece Mainshaft 1954-71

Bush

Drive Member - 10-Spline is the drive coupling at the outer end of the axle, forming part of the wheel hub and drive assembly. Its 10-spline inter...

4WD Selector Rod for the Series transfer box. It forms part of the four-wheel-drive engagement linkage, transmitting selector movement through the...

Wheel Nut, Flat Type secures the road wheel to the hub studs. It has a flat, single-chamfer seating face and a 27mm hexagon.

Gear Lever Knob threads onto the top of the main gearbox gear lever to form the hand grip used for gear selection. It gives the driver a defined c...

Track Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...

Light Socket for the inspection lamp on Series Land Rover vehicles. This black bayonet-type bulb holder is used in the inspection lamp assembly, p...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Rear brake drum installed in the rear drum brake assembly of the vehicle braking system. The drum mounts to the rear hub and rotates with the wheel...

Clutch Plate is the friction-lined driven plate of the clutch assembly, 9 inch (229 mm) diameter. Its splined hub engages the gearbox input shaft ...

Clutch Cover is the pressure plate assembly of the clutch, 9 inch (229 mm) diameter, coil-spring type with three release fingers. It bolts to the ...

Drop Arm for the manual steering box. The drop arm splines onto the steering box rocker shaft and converts the box's rotary output into the fore-an...

Fuel Filler Hose

Handbrake Return Spring is part of the transmission-mounted drum-type handbrake, acting on the relay lever within the parking brake mechanism. Whe...

Exhaust Manifold bolts to the exhaust ports on the cylinder head and collects the exhaust gases from the cylinders into a single outlet feeding the...

Axle Check Strap limits the downward travel of the rear axle, fitted within the rear suspension on the 1-Ton chassis running the Salisbury axle. I...

Accelerator Cable links the accelerator pedal to the injection pump throttle lever, forming part of the throttle linkage on the 2.25L diesel engine...

Choke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...

Fitment: All models to 1980 except V8

Rear Axle Stub for the rear axle assembly on early Series Land Rovers. The axle stub is the outboard section of the rear axle shaft assembly, carr...

Gearbox Gasket Kit - No Seals for the 4-speed manual gearbox and transfer box on Series models. This set supplies the paper and fibre mating gaske...

Side Lamp Lens in white glass for the Lucas military-pattern side lamp. The lens presses into the side lamp body to seal the bulb aperture and diff...

Thermostat for the engine cooling system, with an 82°C opening temperature. The thermostat regulates coolant flow between the engine and the radia...

Round Mirror Head is the circular exterior mirror glass and housing that mounts on a wing- or fender-mounted mirror arm. It gives the driver a rea...

Hub Nut Spanner for the front hub and wheel bearing assembly. The 52mm tool engages the hub retaining nut on the front stub axle. Designed for use...

Clutch Slave Cylinder Bleed Screw for the hydraulic clutch release circuit. It threads into the clutch slave cylinder, at the highest point of the ...

Starter Pinion Retaining Kit for the inertia (Bendix) drive of the starter motor fitted to 4-cylinder and 6-cylinder petrol engines. The starter p...

Track Rod End for the steering linkage, with a right-hand thread. The track rod end is a ball-jointed coupling at the end of the track rod that co...

Gasket

Gearbox Gasket for the LT76 four-speed gearbox with integral transfer assembly. It seals a mating housing face within the gearbox and transfer cas...

Primary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...

Grommet

Drive Screw with a round head, a general body and chassis fixing. The steep-helix thread lets the screw be driven into a pre-drilled hole with a h...

Halfshaft Retaining Collar fitted to the axle halfshaft to locate and retain the halfshaft bearing on the shaft. The collar is pressed onto the ha...