Allmakes4x4 Parts

Interior and Instrument Light Switch is the dashboard-mounted switch controlling the cabin interior light and the instrument panel illumination. W...

Shock absorber bush (eye), anti roll bar bush

Fuel Tank for the 88" short-wheelbase chassis, forming the main fuel store within the fuel supply system. This is the early front-filler configura...

Clutch Release Bush for V8 petrol applications, located within the clutch assembly at the rear of the crankshaft. The bush seats in the spigot rec...

Circlip for the drive shaft and hub assembly on Land Rover permanent four-wheel drive axles. This circlip locates in a machined groove on the driv...

Spring Bush for the leaf spring suspension system on Series Land Rovers. This rubber bush fits into the spring eye at the front fixed mount and re...

Fuel Filler Breather Hose, part of the fuel filler and tank ventilation system. The hose vents air displaced from the fuel tank during refuelling,...

U-Bolt for the leaf spring suspension, clamping the front leaf spring to the axle. This is the short, round-top type with a 7/16" BSF thread. It p...

Railko Bush is the lower swivel bearing in the front axle swivel pin housing. It locates the bottom swivel pin and provides the low-friction pivot...

Shackle Pin (9/16 UNF × 4-3/8 in.) for the rear leaf spring assembly on Land Rover Series vehicles. This is the short shackle pin, fitted at the r...

Shackle plate

Wheel Brace for loosening and tightening road wheel nuts. It has a 15/16 in AF (approximately 24mm) hexagon socket, sized for the wheel nuts fitted...

Thermostat for the engine cooling circuit, controlling coolant flow between the engine and radiator. The valve stays shut while the engine warms f...

Upgrade and restore the swivel housing assembly on your Land Rover Series 2 with this swivel pin conversion kit. Designed for improved durability a...

Waterpump pulley

lock washer. sold EACH.

Thermostat Gasket for the thermostat housing on the 2.25L petrol engine. This paper gasket seals the thermostat housing to the cylinder head, prev...

Track Rod Tube - 109.5cm - Part-Threaded Ends

Bottom End Gasket Set for the overhaul of the 2.25L diesel engine (3- and 5-main-bearing), covering the gasket and joint requirements of the lower ...

Grab Handle for the rear end door, mounted externally on the rear door casing. It provides a fixed handhold at the rear of the vehicle, giving a s...

Washer used within the ignition system of four-cylinder petrol engines, associated with the distributor, ignition coil, HT leads and spark plug ins...

Exhaust Front Pipe for the 2.25L petrol engine, forming the first section of the exhaust system between the manifold and the intermediate pipe. It...

Axle Breather for the front axle housing on vehicles without a remote breather pipe assembly. This screw-in vent allows the air inside the front a...

Drain Plug Washer in copper, used to seal axle differential drain plugs against oil leakage. This copper crush washer seats under the drain plug a...

Breather Set Screw secures the breather to the rocker cover within the engine crankcase ventilation arrangement. It retains the breather against t...

Tappet kit

Flywheel Ring Gear for four-cylinder petrol engines. The ring gear is shrink-fitted to the periphery of the flywheel and meshes with the starter mo...

Exhaust Downpipe is the front section of the exhaust system, connecting the exhaust manifold outlet to the intermediate pipe. This downpipe fits L...

Headlamp Bulb - 12V 40/45W Non-Halogen - LHD

Ignition Coil for the AJ-V8 petrol engine. This coil is of the coil-on-plug type, fitted one per cylinder, mounting directly over the spark plug to...

Crankshaft Pulley Bolt for the AJ-V8 petrol engine. It secures the crankshaft pulley and torsional vibration damper to the nose of the crankshaft, ...

Exhaust Valve for the AJV8 petrol engine, fitted in the cylinder head valvetrain. It opens to release combustion gases into the exhaust port and s...

Cylinder Head Gasket - LH seals the left-hand cylinder head to the engine block on the 4.2L V8 Supercharged petrol engine. It forms the gas-tight ...

Water Pump Gasket

Timing Cover Seal for the AJV8 petrol engine - a rubber seal fitted to the timing gear cover. It seals the timing gear cover against the cylinder ...

Crankshaft Oil Seal – Rear seals the rear of the crankshaft where it exits the cylinder block, retaining engine oil at the crankshaft-to-transmissi...

Battery - Wet Non-Spillable for the vehicle electrical system. It is a flooded (wet) lead-acid battery of sealed, non-spillable construction. It su...

Coolant Outlet Gasket for the engine cooling system, sealing the coolant outlet flange where it joins the engine on V8 applications. The gasket fo...

Door Seal A general-purpose door aperture weather seal, suited to the front doors, rear side doors and rear door/tailgate openings. It seals the g...

Door Seal The lower rear door seal for the left-hand front door, sealing the lower rear edge of the door against the body. It forms part of the fr...

Door Seal The lower front door seal for the left-hand door, sealing between the front door and the bulkhead. It forms the weather seal along the l...

Lower Door Panel forms the bottom half of the two-piece door assembly, for the Left Hand (LH) side. It is the lower structural panel of the door b...

Door Bottom - RH is the lower repair section of the right-hand front door. It replaces the corroded or damaged bottom portion of the door frame, r...

Bonnet Buffer for the Land Rover bonnet assembly. This rubber buffer mounts to the body structure and provides a cushioned contact point for the u...

Front Door Hinge mounts the front door to the body pillar, carrying the door's weight while allowing it to pivot open and closed. The hinge locate...

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Engine Plug is a core (welch) plug that seals the casting holes in the engine. Fitted to the cylinder block, cylinder head water jacket and inlet ...

Window Channel - Top is the upper glass-run channel that guides the top edge of the window glass, supplied as a 94 cm length. It forms the running...