Britpart Parts

4-Pin Relay is a multi-purpose electromechanical switching relay used throughout the vehicle's electrical system, where a low-current control signa...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Plain Washer - metric M8 plain washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...

Bracket

Water Pump for the Rover V8 petrol engine, of the viscous-drive type. It mounts to the front of the engine and forms part of the engine cooling cir...

Hex-head screw, 5/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and so...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

Brake Pad Set for the front axle disc brake assembly, for use with vented front discs. The pads locate within the front calipers and clamp against ...

Headlamp Box is the pressed-steel mounting panel that forms the right-hand (offside) headlamp recess within the front wheelarch and valance assembl...

Track Rod End for the left-hand side of the steering track rod linkage. The track rod end forms the articulating ball-joint that connects the track...

Track Rod End for the right-hand side of the steering track rod linkage. The track rod end forms the articulating ball-joint that connects the trac...

Adjustable A-Frame Ball Joint for the rear suspension upper link (A-frame) assembly. The joint sits at the apex of the A-frame and connects the up...

Reservoir bracket

Split Pin: a cotter pin that locks a slotted (castle) nut or retains a clevis pin. After fitting, its legs are bent back to stop the fastening work...

jet assy

Clevis Pin for the handbrake (transmission parking brake) linkage. This 22mm clevis pin connects the handbrake operating rod to the relay lever, t...

Power Steering Pipe - the return line in the power steering hydraulic circuit. It carries low-pressure fluid from the steering box back to the pow...

Pipe Clamp for the engine oil cooler pipe circuit. This clamp plate secures the oil cooler pipes in the engine bay, restraining them against vibra...

Left-Hand Exhaust Downpipe for the 3.5L V8 EFI engine, non-catalyst exhaust configuration. Connects the left cylinder bank exhaust manifold outlet ...

clamp exhaust pipe RRclassic (with twin exhaust pipes)

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Oil Sump Drain Plug, bolt and washer assembly, for the Rover V8 EFI engine. The drain plug seals the oil sump drain aperture at the base of the en...

Front Steel Winch Bumper with a black protective finish, replacing the standard front bumper to add front-end protection and an integral winch moun...

Rear Radius Arm locates the axle and controls its fore-and-aft movement, with geometry set for a 2 inch suspension lift. The revised arm restores ...

Britpart Coil Springs - Rear - Heavy Load - +2" Lift - Defender 90/Disco 1/Disco 2/RRC

Waterproof Seat Cover Set for the rear seats, tailored to the split rear bench. The set contains a cover for the two-seat section (back and base),...

Stainless Braided Brake Hose Kit - a set of flexible brake hoses for the hydraulic braking circuit, supplied in +40mm extended lengths for vehicles...

Rear Dislocation Cone is a suspension component for the rear coil springs, fitted at the spring seat to guide a spring that unseats at full droop b...

Thrust Washer for the differential assembly within the LT230 transfer box. This 1.35mm thrust washer sits within the LT230 centre differential, co...

Thrust Washer is a 1.25mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Front Cover to Gearcase Gasket seals the joint between the front cover and the main gearcase on the LT77 5-speed manual gearbox. This gasket preve...

Upgrade your Defender, Discovery 1, or Range Rover Classic with this Cellular Dynamic +2" (50mm Lift) rear shock absorber, engineered for exception...

Front Shock Absorber is a cellular-dynamic damper for the front axle, valved for a +2in (50mm) raised ride height. It uses a cellular foam insert ...

Ensure a secure and reliable installation of your heavy-duty rear bumper with this fitting kit, specifically designed for bumper part DA5647. This ...

Winch Bumper Fitting Kit - the mounting hardware set for installing the DA5621 steel winch bumper. Supplies the fixings needed to attach the bumpe...

Brake Disc for the front axle, solid (non-vented) type. Part of the braking system, the disc provides the friction surface the brake pads clamp ag...

Cold Air Intake Filter replaces the complete air filter box in the induction system with an exposed reusable filter, drawing cooler air to the engi...

Coil Spring Conversion Kit that replaces the Electronic Air Suspension (EAS) with conventional coil springs, eliminating the recurring faults and m...

Bush Kit - Radius Arm - Polyurethane

Battery Tray is the offside (right-hand) carrier tray that supports and locates the battery in the engine bay. It forms the mounting platform on w...

Tow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...

Fulcrum Bracket - High Articulation forms the apex mounting of the rear A-frame - the triangulated top link that locates the rear axle and controls...

Instrument Voltage Stabiliser for the Range Rover Classic instrument cluster assembly. This component regulates the voltage supply to the instrume...

Bolt - 1/4" UNC x 1-7/8" is a UNC hex head bolt used in the engine cooling and air conditioning systems of Land Rover vehicles fitted with the 3.5L...

Engine Mounting - bonded rubber-to-metal mount within the engine mounting assembly of 4-cylinder Land Rover engines. It locates between the engine...

Glazing Rubber Seal for the front door drop glass lift channel on the Discovery 1 and Range Rover Classic. This rubber strip seats inside the wind...

Front Floor Crossmember for the body floor structure on the Discovery 1 and Range Rover Classic. This crossmember spans the width of the floor pan...