for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Fuel Tank Breather Hose for the fuel filler and tank ventilation circuit. Connects the fuel tank to the filler neck, venting the tank so that air ...
View full detailsRubber Head Plug closing a machined oil-way opening on the 200Tdi 2.5L four-cylinder turbo diesel engine. The rubber plug seals an oil gallery ope...
View full detailsGlow Plug for the diesel cold-start pre-heating system, threaded into the cylinder head to project into the combustion chamber (or pre-combustion c...
View full detailsFront door handle LH 2A 90/110
Power Steering Reservoir
Flasher lamp front replacement from 1995 on
Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...
View full detailsFront Door Sill Seal fits along the lower door aperture as part of the body sealing system, sealing the threshold at the base of the front door ope...
View full detailsLoadspace Mat Retainer for the rear door aperture at the tailboard. The retainer is a profiled strip that clamps the rear door weatherseal and the...
View full detailsHeater Hose carries engine coolant between the valve and the heater tap, forming part of the heater coolant circuit that feeds the heater matrix. ...
View full detailsHeadlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...
View full detailsOil Seal for the front output shaft of the LT95 gearbox, sealing the transfer case around the rotating output shaft. The LT95 is a combined main g...
View full detailsMounting Stud
Lock Nut with a 5/16" BSF thread. The lock nut secures a threaded fastening against loosening under vibration, maintaining clamp load in service. ...
View full detailsFlywheel Housing Stud - a mounting stud at the flywheel housing. Threaded into the housing, it provides the fixed stud onto which the mating compo...
View full detailsLamp Guard Distance Piece - spacer for lamp guard mounting hardware. The distance piece fits between the lamp guard frame and the light body or mo...
View full detailsSpring Clip - a retaining clip in the transfer gearbox selector linkage. It secures the transfer lever to its pivot, holding the gear-change lever...
View full detailsPlenum Hose - Breather T-Piece to Plenum
Track Rod End with right-hand thread, fitting at the outer end of the track rod within the steering linkage on the Defender, Discovery 1, and Range...
View full detailsUniversal Joint for the propeller shaft assembly, transmitting rotational torque between adjoining shaft sections while permitting the angular move...
View full detailsWater Pump for the Rover V8 EFI petrol engine, supplied with gasket. The water pump sits in the engine cooling circuit and is belt-driven from the...
View full detailsUniversal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...
View full detailsGlass Fuse rated at 15A, a cartridge-type fuse used in the vehicle electrical system. The fuse seats in the fuse box or an inline fuse holder and ...
View full detailsIgnition switch
Bumper Bolt Set in stainless steel - the fixing kit that secures the front bumper to the chassis front cross-member. This kit includes 4 x M10 x 1...
View full detailsClutch Master Cylinder Reservoir Cap for the clutch hydraulic actuation circuit. Seals the fluid reservoir at the clutch master cylinder, retainin...
View full detailsGearbox Gasket Set for the LT95 four-speed gearbox fitted behind the V8 petrol engine. The LT95 is a combined main gearbox and transfer unit. The ...
View full detailsDoor Hinge - right-hand door hinge that mounts the side door to the body hinge pillar and carries the door as it swings. Steel hinge for the front...
View full detailsFlange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...
View full detailsTiming Belt Kit for the camshaft drive of the 2.5L 300 Tdi turbo-diesel engine. The timing belt synchronises crankshaft and camshaft rotation to m...
View full detailsSuspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...
View full detailsFront Bumper Securing Bolt for fastening the front bumper to the chassis crossmember. M10 thread, 120 mm long, with a black finish.
Mudflap Bracket retains the front right-hand mudflap, securing it to the body so the flap hangs correctly behind the front wheel. This is the righ...
View full detailsFuel Tank Cradle
Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...
View full detailsDrive Flange & Mudshield Kit for the Salisbury rear axle. The drive flange bolts to the rear hub and couples the axle half-shaft to the hub, t...
View full detailsDecoke Gasket Set for the 2.5L 300TDi four-cylinder turbo diesel engine. Supplies the gaskets and seals needed to reseal the cylinder head and its...
View full detailsBleed Screw - Metric is the bleed nipple for a disc brake caliper. Threaded into the caliper body, it is opened during brake bleeding to release t...
View full detailsTailgate Cable is a retaining cable for the drop-down rear tailgate on pick-up bodies. It links the rear body panel to the tailgate and limits how...
View full detailsFront Windscreen Wiper Arm for right-hand drive (RHD) applications. Clamps to the wiper drive spindle and carries the wiper blade across the windsc...
View full detailsWater Pump O-Ring Set: the D-ring (O-ring) set for the coolant pump (Land Rover description 'Set-coolant pump D ring'), renewed whenever the pump i...
View full detailsCastle Nut - M12 castellated nut used on the steering and suspension ball-joint fixings. Its slotted crown takes a split pin through the drilled h...
View full detailsDoor Lock Handle (RH) is the exterior handle for the right-hand front door, operating within the door latch and locking assembly. The handle mount...
View full detailsExterior Door Handle for the front right-hand door, left-hand drive configuration. Supplied without a lock barrel aperture. Mounted on the outer d...
View full detailsRubber Buffer moulded door stop pad fitted within the door check and hinge mechanism. The buffer cushions the door against its check arm and limit...
View full detailsDrive Belt Tensioner maintains correct tension on the auxiliary drive belt of the 2.4 and 2.2 TDCi engines. The spring-loaded tensioner pulley bea...
View full detailsWindscreen Strap - a three-hole clamping strap that secures the windscreen frame to the body. It retains the base of the windscreen frame against ...
View full detailsInlet Manifold Gasket End Clamp for the Rover V8 petrol engine. This metal clamp retains the inlet-manifold end seal; it is not the valley gasket o...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →