for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Brake Pipe for the right-hand side of the braking hydraulic circuit, in non-ABS, right-hand-drive applications. This rigid steel pipe carries hydr...
View full detailsAir Intake Blanking Plate closes off the right-hand wing-top air-intake aperture where a cold-air inlet is not required. It fits the same opening ...
View full detailsHose pump to box
Gear Knob - LT95 is the hand grip fitted to the main gear lever of the LT95 4-speed gearbox. It threads onto the top of the gear lever and provide...
View full detailsFront Door Glass Channel Assembly is the run channel that guides the front door window glass within the door frame. It forms part of the front doo...
View full detailsFront cover gasket
Flanged Bolt - M10 x 50, a Grade 10.9 high-tensile fixing used in the front drive shaft and hub assembly. It secures the drive member (drive flang...
View full detailsDrive Belt Bracket and Bearing for the auxiliary (accessory) drive belt system. The bracket mounts to the engine and locates a pulley within the a...
View full detailsBulkhead Outrigger is a structural bracket that supports the left-hand side of the bulkhead and ties it to the chassis frame, carrying the load whe...
View full detailsRear axle right-hand brake caliper assembly used within the rear brake discs and calipers system. This component forms part of the hydraulic brak...
View full detailsExhaust Olive - a conical sealing ring fitted at an exhaust pipe joint, at the silencer-to-tailpipe connection. It seats between the mating pipe s...
View full detailsExhaust Olive for the exhaust system. This tapered sealing ring fits into the slip joint between two exhaust pipe sections. As the joint clamp is ...
View full detailsCam Cover Gasket for the 2.4L Duratorq TDCi (Puma) diesel engine, sealing the camshaft cover to the cylinder head. It forms the oil-tight joint be...
View full detailsCrankshaft Damper mounts on the nose of the crankshaft and forms part of the front-end accessory drive on the Td5 2.5L 5-cylinder turbo diesel. It...
View full detailsLock set 1 barrel 2 keys from 2002 onwards
mud flap LH rear (NO LOGO!) Geschikt voor 110" en 130" BEHALVE High Capacity Pick Up (HCPU). Linksachter.
Raised Air Intake - a steel snorkel that relocates the engine air intake from the inner wing up to roof-line height along the right-hand windscreen...
View full detailsPrimary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...
View full detailsGearbox Gasket for the LT67 manual gearbox. The gasket seals a mating joint on the gearbox casing, maintaining the oil seal between components and...
View full detailsManifold Stud - a mounting stud for the manifold. Threaded into the cylinder head, it locates the manifold and clamps it to the head face via its ...
View full detailsReverse Lamp is part of the rear lighting assembly, mounted at the rear of the vehicle. The lamp illuminates the ground behind the vehicle when re...
View full detailsFuel Pipe from the Td5 2.5L 5-cylinder turbo diesel fuel system, running on the low-pressure side between the inline fuel filter and the pump. It ...
View full detailsLock Washer fitted under a nut or bolt head to resist loosening from vibration. An M10 shakeproof (external-serrated) washer. The serrated teeth b...
View full detailsRear Output Shaft Flange for the LT230 two-speed transfer case. The LT230 distributes drive to the front and rear propshafts. This flange mounts o...
View full detailsFront brake caliper piston repair kit used within the front brake disc and caliper assembly. The components install inside the hydraulic caliper ...
View full detailsRear Brake Caliper, right-hand side, for the rear braking circuit on models fitted with solid (non-vented) rear discs. The caliper clamps the brake...
View full detailsScrew used as a securing fastener in the pedal box area and in brake pipe routing. This screw retains the cover plate at the top of the pedal box,...
View full detailsRear Brake Disc, solid (non-vented) type, mounting to the rear hub to form the friction surface for the brake pads. As the pads clamp against it, ...
View full detailsAir Filter Element for the engine air intake system, housed within the air cleaner assembly. It traps airborne dust and abrasive debris from the in...
View full detailsSide Repeater Lamp
Ignition heater plug timer glow plug relay
Coolant Temperature Transmitter is the engine coolant temperature sender, threaded into the cylinder head where it reads the temperature of the coo...
View full detailsSpeedometer Cable is the lower section of the speedometer drive line. This flexible drive cable transmits the rotation taken from the transmission...
View full detailsAccelerator Cable in the throttle control linkage, connecting the accelerator pedal to the fuel injection pump. It transmits pedal movement to the...
View full detailsAccelerator Cable - 2.5 Diesel - LHD
Lower Spring Seat locates the base of the coil spring in the suspension. It provides the lower bearing surface on which the road spring rests, pos...
View full detailsRadius Arm Washer is a plain washer used at the radius arm mounting in the suspension. It seats under the radius arm fastener to distribute clampi...
View full detailsFir Tree Fastener push-in fixing used to retain body trim and exterior panels against the bodywork. The tapered fir-tree shank pushes into a pre-d...
View full detailsBrake Pedal Box Gasket for the pedal box assembly. It seals the joint where the brake pedal box mounts to the bulkhead, keeping water and draughts ...
View full detailsDoor Hinge & Check Strap Pivot Bracket for the door hinge assembly. It provides the pivot mounting point for the door check strap, which limits...
View full detailsGlazing Rubber is the channel rubber that seats the front door window glass within its lift channel, sized to accept 5mm glass. Part of the door g...
View full detailsDoor Glass Channel (Lift, Front) is the channel fixed along the bottom edge of the front door glass. It grips the lower edge of the window and pro...
View full detailsTailgate latch assembly HCPU
Steering Column Shroud (Lower) is the lower half of the two-part trim cover that encloses the steering column beneath the dashboard. It mates with...
View full detailsWindscreen Glass is the clear laminated glass for the forward body glazing system, installed within the windscreen aperture and bonded to the body ...
View full detailsRear brake shield RH
Collapsible spacer transfer box
Speedometer Drive Housing is the pinion (spindle) housing that fits to the rear flange of the LT230 transfer box. It carries the speedometer drive ...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →