for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Half Shaft Shim - 0.60mm is a 0.60mm selective shim used to set the endfloat of the axle half shaft within the hub assembly. It is fitted at the d...
View full detailsWheelarch Eyebrow is the front wheelarch eyebrow moulding, part of the front wheelarch trim assembly. It mounts to the upper section of the front ...
View full detailsChangeover Relay - 5-Pin - Green is a standard 5-pin changeover relay used across multiple electrical circuits. This relay is used in various appl...
View full detailsFront Axle Shim, 0.45mm thick. Fitted to the front axle half-shaft assembly to set the correct end-float, taking up clearance so the shaft is posit...
View full detailsDoor Glass Drain Channel vertical run channel at the rear edge of the front door glass aperture. The channel guides the door glass along its rear ...
View full detailsBolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...
View full detailsNut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...
View full detailsBolt with a 1/4" UNF (Unified Fine) thread. A threaded steel fastener used to secure body panels and ancillary fittings.
Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...
View full detailsWheel Hub Stud FRC5926 or RUF000020 for Defender 90 And 110, Discovery I and Range Rover Classic.
Radiator & Intercooler Assembly - the front-mounted engine cooling unit for the 300 TDi 2.5L 4-cylinder turbo diesel, combining the coolant rad...
View full detailsFulcrum Bracket for the rear suspension A-frame assembly. The bracket provides the chassis mounting point for the A-frame ball joint, which locate...
View full detailsEngine Front Cover forming the forward housing of the timing drive assembly on the 300Tdi 2.5L four-cylinder turbo diesel engine. The cover bolts ...
View full detailsFront Coil Spring - Medium Duty, +2" Lift (Terrafirma). These front coil springs raise ride height by approximately 2 inches over standard and are...
View full detailsFront Sill Panel for the left-hand side of the body, the outer panel running along the lower bodyside below the front door aperture. The sill clos...
View full detailsIntercooler Pipe for the charge air circuit on the Td5 2.5L 5-Cylinder Turbo Diesel engine. This rigid pipe carries compressed charge air between ...
View full detailsFuel Tank with integral skid guard for the fuel storage system. The pressed-steel tank incorporates a welded underside skid guard that shields it ...
View full detailsAir Duct Seal - seals the heater air duct against the parcel tray within the HVAC air distribution. For vehicles without air conditioning.
Stub Axle Bolt Fixing bolt that secures the stub axle to the axle case. Clamps the stub axle onto the axle housing as part of the hub and stub axl...
View full detailsCrankshaft Pulley mounts on the front of the crankshaft on the 200TDi 2.5L turbo diesel engine and drives the auxiliary drive belts. This pulley i...
View full detailsTiming Cover Gasket for the 200 TDi diesel engine, sealing the front (timing) cover to the front face of the cylinder block. It seals the joint be...
View full detailsFootwell Panel - Right-Hand, Left-Hand Drive is a weld-in repair panel for the right-hand front footwell of the floor assembly. It replaces the or...
View full detailsSafari Door Bolt Kit - a stainless steel fixing set for the rear safari (third) door, for Non-Puma applications. The bolts secure the fixings of t...
View full detailsBonnet Insulation Pad for the engine bay sound-and-heat insulation system. Fits to the underside of the bonnet, where it dampens engine noise tran...
View full detailsRear Fog Lamp Switch is the dashboard-mounted push-button control for the rear fog lamp circuit. This switch allows the driver to activate the rea...
View full detailsCable Gaiter - Door Wiring is a protective sleeve and grommet fitted at the door aperture of the Defender body, routing the door wiring harness saf...
View full detailsInstrument Panel Dash Mounting for the instrument binnacle assembly. This structural mounting bracket secures the instrument panel within the dash...
View full detailsFits Land Rover Defender models (2007-2016) Clear lens wit orange bulb designed for a sleek, modern look
LED Side Repeater is an amber side repeater lamp within the exterior signalling circuit, mounted in the front wing aperture. Each lamp provides la...
View full detailsFuel tank filler hose pipe
Fuel Pump & Sender - in-tank low-pressure fuel pump and fuel level sender assembly for the Td5 2.5L 5-cylinder turbo diesel. The unit mounts v...
View full detailsFuel Tank Cradle from the rear fuel tank mounting - the steel support frame that carries the classic-pattern plastic fuel tank beneath the chassis....
View full detailsClutch Control Valve is fitted in the hydraulic clutch release circuit between the master cylinder and the concentric slave cylinder. It regulates...
View full detailsCV Joint Circlip - the retaining circlip that secures the constant velocity (CV) joint to the front drive shaft. The circlip locates in a groove o...
View full detailsBracket
Water Pump for the engine cooling circuit of the 2.5L 4-cylinder naturally aspirated diesel, petrol and pre-TDi turbo diesel engines. Belt-driven f...
View full detailsBrake Caliper Piston for the hydraulic disc brake caliper, 46mm diameter and 30.68mm height. The piston sits within the caliper bore and transfers...
View full detailsFuel Tank Sender Unit for the petrol fuel level sensing circuit. The sender uses a float arm connected to a variable resistor to measure the fuel ...
View full detailsCountersunk Screw is used to secure side door latch strikers on the Defender. The striker is the fixed plate in the door aperture that the door la...
View full detailsDecoke Gasket Set for the cylinder head assembly of the 2.5L four-cylinder turbo-diesel (200/300 TDi) engine. Provides the gaskets and seals requi...
View full detailsBrake Caliper for the left-hand front wheel, part of the front disc brake assembly in the hydraulic braking circuit. The caliper houses the piston...
View full detailsBrake Caliper for the right-hand front wheel, part of the front disc brake assembly in the hydraulic braking circuit. The caliper houses the pisto...
View full detailsRotor Arm - Ducellier Type for the ignition distributor assembly. This rotor arm fits the Ducellier-type distributor and rotates inside the distri...
View full detailsKickdown Cable Assembly for the automatic transmission control. The cable links the throttle to the automatic gearbox, relaying throttle position s...
View full detailsPiston Ring Set for the 2.25L and 2.5L naturally aspirated diesel engine, supplying the ring pack for one piston. The rings seat in the piston rin...
View full detailsPiston for the 2.25L 4-cylinder petrol engine, forming the reciprocating member within the cylinder bore that transmits combustion pressure through...
View full detailsPower steering seal kit
Steering Lever - RHD for the Adwest power steering box, supplied with the ball joint fitted. Also known as the drop arm, the lever clamps onto the...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →