for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Wiper Cable Tube - LHD is a guide tube in the cable-and-rack windscreen wiper system, in the left-hand-drive configuration. It houses and routes t...
View full detailsFuel Cooler for the diesel fuel return circuit. Mounted in the return line between the fuel injection system and the tank, it dissipates heat pick...
View full detailsFuel Pump Seal for the fuel tank sender unit. This seal seats at the mounting flange of the fuel pump and sender unit where it interfaces with the ...
View full detailsRadiator Hose – Top for the engine cooling system. The upper hose carries hot coolant from the engine outlet to the top of the radiator, where heat...
View full detailsRear Exhaust Tail Pipe for the Land Rover Defender 90. This is the rearmost section of the exhaust system, connecting to the rear silencer outlet ...
View full detailsBrake Hose is a flexible hydraulic line in the braking circuit, carrying fluid from the rigid chassis-mounted brake pipe to the caliper or wheel cy...
View full detailsPedal Pad is the moulded rubber cover that fits over a foot pedal within the pedal box assembly, providing a non-slip contact surface for the drive...
View full detailsAccelerator Cable for the throttle control linkage, transmitting accelerator pedal movement to the carburettor throttle on the 2.25 litre petrol en...
View full detailsFuel Tank Bracket for securing the fuel tank to the vehicle chassis. This metal bracket forms part of the fuel tank mounting assembly, locating an...
View full detailsTop Coolant Hose - the upper radiator hose in the engine cooling circuit. It carries hot coolant from the engine outlet to the top of the radiator...
View full detailsSteering Drag Link - With Bracket - 73cm is a steering linkage rod, supplied with an integrated steering damper bracket. The drag link transmits s...
View full detailsRadius Arm Bush Set - Front - Polyurethane is a set of four polyurethane bushes for the front radius arm-to-chassis mountings. The radius arms loc...
View full detailsLower Spring Seat forms the mounting platform for the base of the coil spring on the axle within the suspension. It locates the foot of the spring...
View full detailsExhaust Y-Pipe is the front section of the exhaust system, merging the outlets from both cylinder banks of the 3.5L V8 petrol engine into a single ...
View full detailsWindow Channel top run channel for the front door glass, fitted within the door frame aperture. The channel lines the upper edge of the window ope...
View full detailsFacia Panel Assembly - LHD is the end closing trim for the upper dashboard fascia on left-hand drive Defender 90 and 110, finished in black. This ...
View full detailsCleat Rope Hook Body Side All and Classic (Softtop) - Series Defender
Door Sill Seal rubber weatherseal for the lower edge of the rear side door aperture, left-hand side. The seal runs along the sill of the door fram...
View full detailsInner waist seal 90/110/130 classic Defender
Door Latch - push-button type latch assembly for the right-hand rear side door. It mounts inside the door and engages the body-mounted striker to h...
View full detailsBonnet Striker Pin - the pin the bonnet latch engages to hold the bonnet closed. It mounts to the bonnet and drops into the body-mounted catch, loc...
View full detailsDoor Checkstrap Cover for the front left-hand door, the trim cap that fits over the door check (checkstrap) mechanism. The checkstrap limits how f...
View full detailsGearbox Tunnel Cover in moulded rubber for the transmission tunnel. It fits over the tunnel around the gear and transfer levers, giving a finished ...
View full detailsDoor Stud used in the front door assembly, securing the door top frame to the door. The stud passes through the door top frame flange and clamps i...
View full detailsRear Wheelarch Moulding is an eyebrow-style trim moulding that fits over the rear wheelarch flange on the outer bodyside, supplied in a gloss finis...
View full detailsQuarter Panel Valance - LH for the Defender 110 Station Wagon. This pressed steel valance panel forms the lower rear section of the left-hand rear...
View full detailsDoor Seal - Bottom for the left-hand front door, forming part of the door-aperture weather sealing. The seal fits along the lower edge of the door...
View full detailsSpare Wheel Bonnet Buffer is a rubber buffer for the bonnet-mounted spare wheel carrier. It sits between the spare wheel and the bonnet, cushionin...
View full detailsHead Gasket - TD5 - 1-Hole seals the joint between the cylinder head and cylinder block on the Td5 2.5L 5-cylinder turbo diesel engine. The 1-hole...
View full detailsDrive Flange is a torque-transmitting flange fitted to the manual gearbox output. It provides the bolted coupling that carries drive from the gear...
View full detailsAlloy Wheel is a single-piece 16 x 7-inch alloy road wheel finished in black. It has a five-stud 5x165 mm bolt pattern and an ET20 offset, which s...
View full detailsLocking Plate - the lower tailboard locking plate, mounted to the rear body. Fitted at the lower hinged tailboard, the plate provides the fixed en...
View full detailsBrake Master Cylinder
Inlet Manifold Seal seals the joint between the inlet manifold and the cylinder head on the 2.4L Duratorq TDCi diesel engine. It maintains an airt...
View full detailsGlow Plug is an electric heating element that warms the combustion chamber to assist cold starting of the 2.4L Duratorq-TDCi (Puma) diesel engine. ...
View full detailsMounting assy Defender 7A752070 to BA407819
Swivel Pin Housing Oil Seal for the front axle swivel and stub axle assembly. This is the outer seal, fitted at the interface between the stub axle...
View full detailsRear Prop Shaft for the rear driveline, connecting the transfer box rear output flange to the Salisbury rear axle differential pinion. The propell...
View full detailsStub axle
Front Propshaft for 4-cylinder applications, forming part of the drivetrain. It transmits drive from the transfer box front output flange to the fr...
View full detailsHalf Shaft Shim is a 1.05mm selective shim used in the front axle drive shaft and hub assembly. It sets the endfloat of the front half shaft drive...
View full detailsO-Ring - LT95 Gearbox seals the transfer shaft on the LT95 4-speed gearbox, which carries an integral transfer case, preventing oil leakage at the ...
View full detailsSeat yoke
O-ring
Gearbox Gasket seals the top cover to the main casing of the LT77 five-speed manual gearbox, forming an oil-tight joint between the top cover plate...
View full detailsSwivel Pin is the upper pin of the front axle swivel assembly. It bolts to the top of the swivel housing and carries the upper bearing about which ...
View full detailsGearbox Gasket seals the transfer box side cover joint on the LT85 five-speed manual gearbox, forming an oil-tight seal between the side cover and ...
View full detailsPower steering pump
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →