for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Battery Clamp - the hold-down that secures the battery in its tray. It bears down on the battery to stop it shifting under vibration and off-road m...
View full detailsFlange rear
Door Latch Foam Gasket seals the latch mechanism at the lockface, fitting between the latch assembly and the door skin. Installed on the front doo...
View full detailsSteering Box Oil Seal Oil seal for the input (worm) shaft of the manual, non-power (Gemmer) steering box, sealing around the shaft where it enters ...
View full detailsCorner Capping Bracket is part of the rear body corner capping assembly, serving as the mounting bracket that secures the corner capping trim to th...
View full detailsIgnition and Starter Switch - the electrical switch unit that mounts to the base of the steering column lock, in the ignition and starting circuit,...
View full detailsSeat Base - Techno Style The base cushion of a front seat, forming the seating surface that mounts to the seat frame and runners. Finished in the ...
View full detailsEGR Valve to Pipe Gasket for the diesel exhaust gas recirculation (EGR) system. The gasket seals the flanged joint between the EGR valve and the r...
View full detailsFilter Kit - 2.2 & 2.4 TDCi for the Land Rover Defender with the Puma TDCi diesel engine. This kit consolidates the main filter and sealing it...
View full detailsGearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...
View full detailsFlange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...
View full detailsFuel Filler Hose connecting the external fuel filler neck to the fuel tank on the Defender. This rubber hose forms the sealed connection between t...
View full detailsRocker Shaft Clamp for the cylinder head valve train on the 300TDi 2.5L turbo diesel engine. Secures the rocker shaft to the cylinder head pedesta...
View full detailsFuel Return Hose forms part of the fuel return line on the 2.2L Puma TDCi diesel engine. It carries surplus fuel from the injection system back to...
View full detailsA-Post Finisher is the trim cover for the right-hand A-post, the windscreen pillar, concealing the pillar structure and dressing the join between t...
View full detailsDoor Lock Link for the front right-hand door, the operating rod that connects the locking mechanism to the door latch. It transfers movement from ...
View full detailsTiming Belt Tensioner Washer for 200TDi and 300TDi engines. This slotted packing washer fits to the timing belt tensioner assembly, setting the co...
View full detailsFront Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...
View full detailsSeat Belt - Rear Centre Lap - Long End for the rear seat belt assembly in the Defender passenger compartment. This is the long webbing end of the ...
View full detailsTensioner Pulley for the air conditioning drive belt on the 2.5L 300TDi turbo diesel engine. It runs against the accessory drive belt and maintain...
View full detailsBanjo Bolt is a hollow union bolt used in the fuel system of the 200 Tdi and 300 Tdi engines. It secures a banjo hose fitting at the injection pum...
View full detailsCarburettor Float Assembly regulates the fuel level in the float chamber of an SU carburettor, governing the fuel available to the metering needle ...
View full detailsCooling Fan Assembly for the engine cooling circuit, mounted at the front of the engine and driven from the water pump pulley. It draws air through...
View full detailsCooling Fan for the engine cooling assembly. Driven from the front of the engine through the viscous fan coupling, the fan draws air through the r...
View full detailsBody Strap - 2 Hole is a foam mounting spacer used in the front windscreen hinge assembly on the Defender. This two-hole component sits between th...
View full detailsClutch Hose within the hydraulic clutch circuit of the Puma TDCi Defender. The hose carries hydraulic fluid between the clutch master cylinder and...
View full detailsDoor Glass Regulator Shim - a packing shim used at the door window regulator and glass channel. It sets the regulator and channel at the correct st...
View full detailsCable Tie, Panel Fixing: grey cable tie strap with a panel fixing, 4.6 x 165 mm.
Connecting Rod Bolt for the Rover V8 EFI petrol engine, part of the connecting rod assembly in the engine bottom end. The bolt clamps the connecti...
View full detailsFuel Hose for the 3.5L V8 twin-carburettor engine, part of the carburettor fuel supply plumbing. It connects the fixed points in the fuel feed lin...
View full detailsstriker lock LH for "anti-burst" locks. (lift-up type)
Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...
View full detailsHeater grip OEM
Brake Pipe Clip - a triple retaining clip for the brake hydraulic pipework. It holds three brake pipes together along the chassis run, maintaining...
View full detailsElectronic Distributor for the ignition system of the 4-cylinder petrol engine. It distributes high-tension voltage from the ignition coil to each...
View full detailsMain Bearing Cap Bolt for the 2.5L Td5 five-cylinder diesel engine. This bolt clamps a main bearing cap to the cylinder block, retaining the cranks...
View full detailsEGR Cooler Return Pipe for the exhaust gas recirculation (EGR) cooling circuit. This pipe returns coolant from the EGR cooler back to the engine c...
View full detailsBody Mounting Shim used to set the correct clearance and alignment between the body tub and the chassis mounting points. This thin flat shim is us...
View full detailsBreather Adaptor - a threaded fitting in the axle and transfer case ventilation (breather) system. It screws into the axle casing or transfer case...
View full detailsSpring Washer for the fuel tank sender unit and fuel pick-up pipe fixings. Fitted beneath the retaining screws that secure the fuel gauge sender u...
View full detailsABS Sensor - Front for Defenders with the 4 wheel anti-lock braking system. This wheel speed sensor mounts at the front axle hub and continuously ...
View full detailsAlternator Oil Feed Pipe supplies pressurised engine oil to the vacuum pump integrated at the rear of the alternator, on the Td5 2.5L 5-cylinder tu...
View full detailsFuel Pump is a low-pressure in-tank unit forming part of the fuel delivery system on petrol applications. Mounted inside the fuel tank, it acts as...
View full detailsExhaust centre silencer 110 V8 from vin266790
Seat Base Cover for a front outer seat, forming the trim over the seat base cushion. Finished in black vinyl. The cover fits over the front outer ...
View full detailsFuel Leak Off O-Ring seals the leak-off (spill return) connection at a diesel fuel injector. It sits in the injector leak-off circuit that collect...
View full detailsFlanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...
View full detailsFootwell Panel - Right-Hand, Right-Hand Drive is a weld-in repair panel for the offside front footwell of the floor assembly. It replaces the orig...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →