for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Fits Defender 110 (1999 onwards) with 2.5 Td5 Diesel, 2.2, and 2.4 Puma Diesel engines Non-galvanised for a strong, reliable solution 16cm ext...
View full detailsHeadlight Panel Screw Kit in stainless steel, for fixing the front headlight surround panels to the bodywork. The kit contains four 8 x 13 mm self...
View full detailsLight Lens Screw Kit in stainless steel, for retaining the lens covers on the exterior lamp units. The kit supplies the stainless steel screws tha...
View full detailsSeat Belt Bracket for the front seat belt, lower mounting, left-hand side. This bracket bolts to the seat box and provides the lower anchorage poi...
View full detailsDrop Arm for the Gemmer recirculating-ball steering box, forming the output lever of the steering linkage. The drop arm mounts on the splined sect...
View full detailsPlain Washer - metric M8 plain washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...
View full detailsOutput Shaft - MT82 6-Speed Manual Gearbox. The output shaft is located at the rear of the MT82 transmission housing and transmits rotational driv...
View full detailsSpacer 15,1mm Green
Differential Assembly - a reconditioned 4-pin differential unit for the Land Rover-type axle. The differential sits at the centre of the axle, tak...
View full detailsRoof Access Ladder Rear Assembly is a rear-mounted access ladder with an integrated rear lamp guard. It mounts to the rear bodywork to provide saf...
View full detailsInterior Lamp - courtesy lamp for the passenger compartment. Provides interior illumination as part of the interior lighting circuit, typically sw...
View full detailsBrake Fluid Reservoir Kit for the brake master cylinder, on vehicles with and without ABS. The kit includes the fluid reservoir, the cap with low ...
View full detailsBrake Servo Assembly is the vacuum-assisted brake booster in the braking hydraulic system, mounted between the brake pedal linkage and the master c...
View full detailsAccelerator Pedal Pad - the moulded rubber cover that fits over the accelerator pedal. It provides a grippable, wear-resistant contact surface for...
View full detailsDifferential Cover for the Salisbury rear axle. The cover bolts to the rear face of the axle casing, enclosing the crown wheel and differential and...
View full detailsAutomatic Transmission Oil Screen for the ZF 4-speed automatic transmission, fitted within the transmission oil sump. The screen filters the autom...
View full detailsRear Wheel Cylinder (Right-Hand) is the hydraulic actuator within the rear drum brake assembly, mounted to the brake backplate. Under pedal pressu...
View full detailsMainshaft Peg is a locating peg fitted to the mainshaft of the LT67 gearbox. It positions and retains its associated component on the gearbox main...
View full detailsCon Rod Bearing Set - connecting rod big-end bearing shells for the 2.25L four-cylinder engine. The con rod bearings sit between the connecting ro...
View full detailsCon Rod Bearing Set - connecting rod big-end bearing shells for the 2.25L four-cylinder engine. The con rod bearings sit between the connecting ro...
View full detailsLower Steering Shaft Universal Joint for the steering column assembly, forming the lower coupling between the steering column and the steering box ...
View full detailsReverse Light Switch for the LT77 manual gearbox. The switch threads into the gearbox casing and is operated by the selector mechanism when revers...
View full detailsIntercooler Hose - a charge-air hose in the turbocharged diesel induction system. It forms part of the boost circuit that carries pressurised air ...
View full detailsLower Oil Cooler Pipe - return pipe in the engine oil cooling circuit of the 4.0L V8 EFI petrol engine, carrying cooled oil from the oil cooler bac...
View full detailsUpper Oil Cooler Pipe - feed pipe in the engine oil cooling circuit of the 4.0L V8 EFI petrol engine, carrying oil from the engine to the oil coole...
View full detailsHex nut
Oil Pressure Switch - tapered thread, engine lubrication circuit. Screws into the oil gallery - at the pump, the filter housing or the oil cooler ...
View full detailsPower Steering Pump generates the hydraulic pressure that drives the power steering system. Engine-driven, it draws fluid from the reservoir and d...
View full detailsChoke Cable operates the carburettor choke from the driver's control within the fuel and cold-start system, for the 2.5L 4-cylinder petrol carburet...
View full detailsAxle Breather Pipe Clip from the axle breather system, retaining the breather hose along its run from the axle case up to its higher mounting point...
View full detailsExhaust Downpipe for the Land Rover Defender fitted with the 4-cylinder 2.5-litre naturally-aspirated diesel engine. This primary exhaust pipe con...
View full detailsDump Valve
Plate - LH is the rear axle brake pipe shield (bracket) for the left-hand side. It mounts on the rear axle and shields the rigid brake pipe runnin...
View full detailsPlate - RH is the rear axle brake pipe shield (bracket) for the right-hand side. It mounts on the rear axle and shields the rigid brake pipe runni...
View full detailsFits Defender 300Tdi, Td5, and 2007-2016 models with a raised air intake Inside diameter: 64mm Ideal for wading and dusty environments, keepin...
View full detailsExhaust Silencer for the front section of the exhaust system. Mounted between the front downpipe and the intermediate silencer, it attenuates comb...
View full detailsCoil Spring for the rear suspension on vehicles equipped with self-levelling suspension. This is the driver-side road spring, identified by its blu...
View full detailsRear Mudflap in the left-hand fitment, mounted behind the rear wheel to deflect road spray, mud and stones thrown up by the tyre. It protects the ...
View full detailsRear Mudflap in the right-hand fitment, mounted behind the rear wheel to deflect road spray, mud and stones thrown up by the tyre. It protects the...
View full detailsSliding Window Catch for the side-opening cab window glazing. This right-hand catch assembly latches the sliding side window in the closed positio...
View full detailsNut Plate for the side door latch striker. It provides the captive threaded mounting for the striker, holding the fixing nuts in alignment on the ...
View full detailsSeat Squab Hinge Link Rod - LH is part of the rear forward-facing split seat squab hinge assembly. The link rod connects the seat squab (backrest)...
View full detailsSeat Linkage for the rear forward-facing split seat assembly. This right-hand link rod (squab hinge link) connects the seat squab hinge to the bac...
View full detailsCheckstrap cover RH
Seat Base Cushion for the inner (centre) position of the 3-person front bench seat assembly. Constructed with a foam core upholstered in black vin...
View full detailsSill Panel Stay is a support bracket for the sill (rocker) panel. Forming part of the sill panel assembly, it braces the sill panel to the body st...
View full detailsOil Sump Drain Plug, bolt and washer assembly, for the Rover V8 EFI engine. The drain plug seals the oil sump drain aperture at the base of the en...
View full detailsFront Indicator Lamp forms part of the front direction-indicator lighting, mounted on the front of the vehicle to signal turns and hazard warning. ...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →