for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Carburettor Float Assembly for the Zenith carburettor used on 2.25L and 2.5L 4-cylinder petrol engines. The float sits in the carburettor float ch...
View full detailsWiper Relay is a 5-pin mini relay used in the wiper control circuit to switch the supply to the wiper motor. The five-pin layout provides a change...
View full detailsDashboard Screw for facia and dash trim fixing - a No.6 x 3/4" countersunk self-tapping screw. Used to secure dashboard and facia trim panels. The...
View full detailsDifferential Lock Link Assembly for the LT230 transfer box, fitted to vehicles with the LT77 or LT85 5-speed manual gearbox (28D prefix). This lin...
View full detailsPlenum Chamber Gasket for the V8 EFI petrol engine, part of the air intake and induction assembly. The gasket seals the joint at the plenum chambe...
View full detailsValve Collet for the valve gear of the 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The split collets seat in the gr...
View full detailsChubby Cubby Box - a between-seats storage box and armrest that mounts on the centre panel of the seat box. It provides lockable interior storage ...
View full detailsOxygen Sensor (lambda sensor) for the V8 EFI petrol exhaust system on catalyst-equipped applications. It measures residual oxygen in the exhaust ga...
View full detailsCamshaft for the valvetrain of the 4.0/4.6L V8 petrol engine. Mounted in the cylinder block and driven from the crankshaft, the camshaft lobes act...
View full detailsHeater Inlet Hose is a moulded coolant hose in the cabin heater circuit of the 200TDi 2.5L turbo diesel engine. It carries hot coolant from the en...
View full detailsKit - Timing Belt - 200TDi
Cubby Box - Black Mesh
Sidelight Bulb, rated 24V 10W, for the front sidelight (parking light) position. The bulb seats in the sidelight holder within the front lamp asse...
View full detailsSport Seats - a pair of low-base front bucket seats finished in black vinyl with a diamond-pattern facing. The sports design pairs a shaped, suppo...
View full detailsClutch Driven Plate for the LT95 four-speed gearbox, V8 petrol. The driven plate (friction disc) is splined to the gearbox input shaft and clamped...
View full detailsCountersunk Screw for the Transmission Brake Assembly. The countersunk head sits flush within the mating surface, maintaining correct alignment and...
View full detailsRadius Arm to Axle Bush Set for the front suspension, within the radius arms and links assembly. These polyurethane bushes fit at the axle-side mou...
View full detailsRadius Arm to Chassis Bush - Front locates the front radius arm to its chassis mounting bracket within the coil-sprung front axle suspension. It f...
View full detailsCirclip - Output Shaft Flange used within the transfer box output flange assembly to retain the output shaft bearing and associated components in p...
View full detailsFront Bush Kit with replacement bushes for the front radius arms and panhard rod. The bushes insulate the front axle location points while absorbi...
View full detailsTiming Belt for the camshaft drive of the 300 TDi diesel engine, running within the timing belt and tensioner assembly at the front of the engine. ...
View full detailsGlazing Rubber is fitted within the side window assembly to secure and seal a fixed window glass to the body aperture. It retains the glazing pane...
View full detailsFuse rated at 7.5A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 7.5 amps, the fuse breaks the connection...
View full detailsBonnet Prop Washer for the Defender bonnet support rod assembly. This washer is fitted to the bonnet prop rod and acts as a bearing/retention surf...
View full detailsLower Steering Column Shroud is the lower half of the trim cover that encloses the steering column below the steering wheel. The moulded shroud co...
View full detailsDrop Arm Nut for the Gemmer 6-bolt steering box on the Defender 90/110 and Range Rover Classic. This hex nut secures the steering drop arm to the ...
View full detailsGearbox Breather for the gearbox and transfer case assembly. This breather is located on the gearbox or transfer case casing and vents internal pr...
View full detailsSill Tread Plates - Chequered - Pair - Black
Body Stay - Lower - Rear - RH Right-hand lower stay forming part of the rear body mounting. It locates the lower rear corner of the body to the ch...
View full detailsDrop Plate Strengthener for the towing equipment assembly. It acts as a spacer and strengthener for the towing jaw and the towing jaw/ball fixings...
View full detailsMainshaft 5th Speed Gear for the LT77 and LT77S 5-speed manual gearbox. This gear is mounted on the mainshaft assembly and meshes with the corresp...
View full detailsEngine Mounting Rubber for the 2.5L 200 TDi engine mounting system. This rubber-to-metal mount locates between the engine mounting foot and the cha...
View full detailsBonnet Catch Plate is the mounting plate for the bonnet slam catch, located in the grille and front panel structure as part of the bonnet release a...
View full detailsWindow Seal: rubber glazing seal for the window glass, sealing it against water and draughts.
Rocker Assembly Aluminium - LH
Relay operates within the anti-theft alarm and central locking circuit. This relay switches power to the alarm and remote central locking system, ...
View full detailsSpring Washer is a split spring washer fitted under a nut or bolt head. Its sprung ends bear against the fastener to maintain tension and resist lo...
View full detailsAnti-Roll Bar Kit comprising both front and rear anti-roll bars for the suspension system, supplied complete with standard rubber bushes and fittin...
View full detailsSteering Column Switch is the multi-function stalk assembly mounted on the steering column. It combines the indicator, headlamp main beam and horn...
View full detailsFront Half Shaft for the right-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant vel...
View full detailsABS Wheel Speed Sensor - front sensor for the four-wheel anti-lock braking system. The sensor mounts in the front axle housing with its pole piece...
View full detailsCylinder Head Gasket Set for the 2.5L 200TDi turbo diesel engine, supplying the top-end gaskets and seals required when the cylinder head is remove...
View full detailsBrake Caliper Bleed Screw - the bleed nipple that threads into the brake caliper. Backing the screw off releases trapped air and old fluid from th...
View full detailsConrod Bearing Kit - 0.010" Undersize for Land Rover four-cylinder petrol and diesel engines. Supplies a complete set of connecting rod big-end bea...
View full detailsRadiator assembly Def TD5 + valve
Clutch Pipe for the lower section of the clutch hydraulic circuit, on 4-cylinder and 300 TDi engines with manual transmission. This rigid pipe car...
View full detailsMud Shield – RHD – LH is the left-hand mud shield for the pedal box. It fits over the pedal box aperture in the bulkhead to keep mud, water and ro...
View full detailsThermostat for the 2.4L Duratorq-TDCi Puma diesel engine, located in the coolant circuit at the oil cooler and filter housing. The thermostat regu...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →