for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Output Shaft Washer - LT230 Transfer Box for the Defender Puma drivetrain assembly. This washer seats behind the output shaft flange at both the f...
View full detailsSteering Column Bolt for the lower steering shaft coupling. This pinch bolt clamps the lower steering shaft to its mating joint, securing the colum...
View full detailsHeater Hose - a coolant hose in the heater circuit, running between the engine and the heater matrix. It carries engine coolant to and from the he...
View full detailsCylinder Block Seal is a 16mm sealing washer fitted to the cylinder block of the Rover V8 petrol engine, closing off a machined passage in the bloc...
View full detailsCamshaft Bearing Set for the Rover 3.5L V8 petrol engine. Supplies the bearing shells that support the camshaft as it runs within the cylinder blo...
View full detailsIdler Pulley for the air conditioning auxiliary belt drive on 300TDi engines. Positioned within the A/C belt routing circuit, this pulley guides t...
View full detailsSteering Valve Ring is a PTFE sealing ring used within the rotary valve of the Adwest power steering box. It seals between the pressure lands of t...
View full detailsGearchange Spring
O-Ring - Oil Pick-Up Pipe for the 2.5L 300TDi 4-cylinder turbo diesel engine. This O-ring seals the oil pick-up pipe connection at the oil pump or...
View full detailsO-Ring for the oil strainer in the ZF 4-speed automatic transmission. This seal fits the oil strainer (the automatic transmission fluid pickup fil...
View full detailsO-Ring seals the intermediate shaft in the LT230 transfer box, sitting between the shaft mounting and the transfer casing to hold the oil seal at t...
View full detailsJoint Washer - LT77 Front Cover seals the mating face between the front cover and the main casing of the LT77 5-speed manual gearbox. The washer p...
View full detailsRocker Cover Breather Hose - Left-Hand for the crankcase ventilation system of the Rover 3.5L V8 twin-carburettor engine. This hose connects the l...
View full detailsseal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)
Magnetic Sump Plug for the ZF 4-speed automatic transmission. This drain plug seals the transmission oil pan at the drain point. Its magnetic tip ...
View full detailsPan Head Screw, M8 x 25mm. Metric pan head screw for use across Land Rover body, chassis, and accessory fitment applications.
Capping Corner Bracket forms the corner joint of the rear body capping trim. This left-hand bracket locates and secures the capping section at the...
View full detailsBattery Clamp Bolt - fastener for the battery retention assembly. Secures the battery clamp bar across the top of the battery, holding the battery...
View full detailsBonnet Prop Stay the manual prop rod that holds the bonnet in the raised position. The stay props the open bonnet and locates in a catch to keep i...
View full detailsBrake Disc - a vented front brake disc for the front axle braking system. The disc rotates with the front wheel hub and is clamped by the caliper ...
View full detailsRear brake disc cross drill & grooved 110 83-06/130 83-06
EGR Cooler Hose - Engine to Cooler is a coolant hose serving the exhaust gas recirculation (EGR) system. It carries engine coolant from the engine...
View full detailsRocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...
View full detailsRocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...
View full detailsFuel Pump Adaptor for mounting the external fuel pump on petrol engines. It provides the interface between the external fuel pump and its mounting...
View full detailsOlive compression ferrule for a pipe union. The olive seats between the pipe and the union nut, forming a compression seal at the joint as the nut...
View full detailsgrab handle for 3rd / 5th door (rear end door). Upto (VIN) 1A622423
Lower Tailboard Bracket is the right-hand bracket for the bottom-hinged rear tailboard, part of the tailboard mounting assembly. It secures the lo...
View full detailsExhaust Manifold for the 2.5L 4-cylinder petrol engine. Bolts to the exhaust ports on the cylinder head and collects the exhaust gases from each cy...
View full detailsSliding Window Catch - LH is the locking catch for the left-hand sliding side window in the rear cab panel of the Defender Hard Top. The catch sec...
View full detailsO-Ring - Diff Lock - LT230 provides the hydraulic seal at the differential lock mechanism and front output shaft location within the LT230 transfer...
View full detailsGear Lever Damper for the LT95 four-speed gearbox gear-change mechanism. This damping washer fits at the base of the main gear lever, absorbing vi...
View full detailsMainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...
View full detailsSeat Re-trim Kit (Inner) re-covers the front centre seat, renewing the cushion and squab foams together with their outer covers to restore the seat...
View full detailsStarter Solenoid for the starter motor on 2.5 litre four-cylinder diesel engines. Mounted on the starter motor within the engine cranking circuit,...
View full detailsOil Pump Relief Valve Spring - sets the pressure at which the oil pump's relief valve opens. It holds the relief valve plunger closed against the ...
View full detailsIdler Pulley for the air conditioning auxiliary belt drive on 300TDi engines. This pulley operates within the A/C belt drive circuit, maintaining ...
View full detailsGearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...
View full detailsCylinder Head Dowel for the V8 petrol engine. The dowel is a locating pin fitted to the cylinder block deck that positively registers the cylinder ...
View full detailsDistributor O-Ring, the sealing ring for the ignition distributor on the 3.5L V8 petrol engine. The O-ring seals the distributor base where it loc...
View full detailsCamshaft Sprocket - GEMS V8 is the timing chain sprocket fitted to the camshaft of the Rover GEMS 4.0L and 4.6L V8 petrol engine. The sprocket is ...
View full detailsOil Separator Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. This gasket seals the oil separator to the cam cover, preventing engine oil ...
View full detailsDrain Plug - Coolant - Cylinder Block is the threaded plug that seals the coolant drain port in the cylinder block, providing a controlled drain po...
View full detailsPan Head Screw, M4 x 12mm. Metric pan head screw for use across a range of Land Rover assemblies, including brake system and electrical components.
Front Coil Spring - front suspension coil spring, seated between the axle spring pad and the chassis spring turret to support the vehicle and contr...
View full detailsNeedle Bearing is an internal roller bearing used within the LT77 5-speed and R380 5-speed manual gearbox assemblies. Needle roller bearings of th...
View full detailsFuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...
View full detailsClip retains the heater and air-conditioning control cable within the HVAC control assembly, holding the cable on its correct routing.
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →