for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Glazing rubber
Heated Flat Mirror Head - the exterior door mirror assembly, fitted with a flat glass and an integrated heating element. The mirror head mounts to...
View full detailsClutch Slave Cylinder Repair Kit for the hydraulic clutch release circuit on V8 petrol applications. The clutch slave cylinder is actuated by hydr...
View full detailsRear door check assy LH
Check Assembly Door Rear - RH
Fitment: All Models Except TD5
Sliding Window Pair - clear glass side windows within the body glazing, supplied as a pair. Each framed unit carries horizontally sliding clear gl...
View full detailsAnti-Roll Bar is the rear stabiliser bar within the suspension system, mounted transversely across the rear axle. Connected to the suspension thro...
View full detailsCrossmember - rear chassis crossmember for the body and chassis structure, supplied in the no-extensions configuration. It is the rearmost structur...
View full detailsABS Pump Relay for the Anti-lock Braking System electrical circuit. A normally open, black-bodied relay that controls power supply to the ABS pump...
View full detailsFloor Panel forms the main floor pressing on the left-hand (nearside) side of the body. This pressed-steel panel spot-welds into the body structur...
View full detailsFront Main Floor Panel for the right-hand side of the cab floor structure. This panel forms the main front floor section on the right-hand side of...
View full detailsLocking Nut - a push-on locking nut for securing interior trim and ducting. It pushes onto a stud or screw thread and grips to hold the fixing cap...
View full detailsVacuum Pump O-Ring that seals the diesel vacuum pump at its mounting joint. The vacuum pump supplies the depression used by the brake servo on die...
View full detailsRear Half Shaft - right-hand - for the Defender with early-type 23-spline CV joint. This solid steel drive shaft transfers torque from the rear di...
View full detailsIgnition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...
View full detailsDistributor Drive Gear - V8
Starter Motor Bush Kit for the diesel engine starter motor. The bushes carry the starter motor armature shaft in its end housings; renewing them r...
View full detailsVacuum unit
Front Stub Shaft forming part of the front axle assembly on the Series 3 Long Wheelbase (109"). The stub shaft sits within the swivel housing and ...
View full detailsMainshaft - Series 3
Layshaft Bearing for the early-type LT76 gearbox. It supports the layshaft (countershaft) within the gearbox, carrying the cluster gear that trans...
View full detailsTaper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...
View full detailsCrankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...
View full detailsShackle Plate for the rear leaf spring shackle assembly. The shackle plate links the rear eye of the leaf spring to the chassis mounting, allowing ...
View full detailsFuel Cap closes and seals the fuel tank filler neck on petrol applications. It uses a two-lug bayonet fixing that locates and locks into the fille...
View full detailsDoor Seal - Front - Top is the weatherstrip that closes the joint between the top edge of the front door and the roof cant rail, forming part of th...
View full detailsRope Hook
Headlamp Bezel is the outer retaining surround for the headlamp unit, mounting within the front lighting panel. It secures and finishes the lamp a...
View full detailsBody Seal - a moulded rubber weather seal in the body & chassis assembly. It closes the gap between adjacent body panels to exclude water, dus...
View full detailsTailgate Hook for the lower hinged tailboard, left-hand side. This pigtail (spiral) hook mounts on the body and retains the tailboard chain, holdi...
View full detailsFront Outer Seat Cushion Base for the adjustable seat frame in Series II, IIA, and III 109" long-wheelbase vehicles. This is the outer seat base c...
View full detailsBarrel Lock and Key, Set of Three for the door locks, supplied as three keyed lock barrels each with a key. Each barrel is the cylinder the key tu...
View full detailsBarrel Lock and Key, Set of Two for the door locks, supplied as two keyed lock barrels each with a key. Each barrel is the cylinder the key turns ...
View full detailsJoint Washer for the LT76 manual gearbox. Fitted between mating faces within the gearbox to form an oil-tight joint on assembly. Supplied as a sin...
View full detailsCamshaft for the 2.25L 4-cylinder petrol engine valve train. Running in the cylinder block and driven from the crankshaft by the timing gear, the ...
View full detailsBrake Servo Repair Kit for the Type 50 vacuum brake servo unit (227mm diameter). This overhaul kit contains the components necessary to rebuild th...
View full detailsClutch Alignment Tool - a centring tool used when refitting the clutch on the 2.4 TD4 diesel engine. It passes through the hub of the driven plate...
View full detailsWheel Cap - LH for the Freelander 1 wheel arch assembly. This left-hand wheel capping is a trim component that covers and finishes the wheel arch ...
View full detailsX-Trouser (Pair)
Starter Motor Solenoid is the electromagnetic switch mounted on the starter motor body, forming the switching element of the engine starting circui...
View full detailsAir Vent Louvre for the dashboard fascia, forming part of the cabin ventilation outlet. This louvre mounts in the dash face and directs air from t...
View full detailsShock Absorber Bush Set for the upper damper mounting, polyurethane. The bushes sit in the upper damper mounting, isolating the damper from its mo...
View full detailsPanhard Rod - front axle lateral location. The panhard rod ties the front axle to the chassis laterally, resisting sideways movement of the axle w...
View full detailsRear Axle Breather Pipe vents the rear axle casing. It equalises internal air pressure as the axle heats and cools, allowing the casing to breathe...
View full detailsSecond Row Door Fixing Kit in stainless steel, providing the mounting bolts and fixings for the middle-row door. The stainless steel construction ...
View full detailsRear Drum Brake Kit, supplied as a single-axle service set for the rear drum brakes. The kit includes the brake shoes, wheel cylinders, brake spri...
View full detailsO-Ring seals the water connection in the engine cooling circuit, located at the thermostat housing area to prevent coolant leakage at the joint on ...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →