for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
EGR Gasket seals the exhaust gas recirculation (EGR) valve connection to the inlet manifold on the 200Tdi and 300Tdi 2.5L four-cylinder turbo diese...
View full detailsDifferential Pinion Bearing Shim - 0.064 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...
View full detailsGearbox Selector Pad for the LT77 five-speed manual gearbox. Fits the 5th gear selector within the selector and yoke assembly, forming the bearing...
View full detailsAutomatic Transmission Shaft is a coupling shaft within the ZF 4-speed automatic gearbox assembly. This shaft transmits drive between internal gea...
View full detailsO-Ring - Diff Lock Selector Shaft - LT230 Transfer Case This O-ring seals the differential lock selector shaft where it passes into the LT230 tran...
View full detailsFlanged Nut - M6 flanged hex nut for use across a wide range of Land Rover assemblies including engine, drivetrain, body, braking, and electrical a...
View full detailsGearbox Oil Seal for the extension case of the LT77 five-speed manual gearbox, sealing the mainshaft output collar. The seal runs on the collar at...
View full detailsA/C Belt Tensioner Cover for the air conditioning belt drive on 300TDi engines. This cover fits over the tensioner pulley assembly in the A/C auxi...
View full detailsSeat Recline Mechanism Cover - RH is the trim cover plate fitted over the front seat recline adjuster mechanism. It conceals and protects the recl...
View full detailsChannel fitted to the top of the rear side door frame, retaining and sealing the upper edge of the fixed quarter light glass. Designed for 4mm glas...
View full detailsGearchange Housing Gasket for the LT85 five-speed manual gearbox. This gasket seals the interface between the gearchange housing and the main gear...
View full detailsHeater Hose - Inlet for the engine coolant and cabin heater circuit on the Td5 2.5L 5-cylinder turbo diesel. Carries hot coolant from the engine f...
View full detailsrestrictor, washer starlock for steering wheel
Battery Wing Nut secures the battery hold-down clamp within the battery mounting assembly, threading onto the clamp rod to hold the battery firmly ...
View full detailsGearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...
View full detailsBolt, 3/8" BSF x 5/8", a British Standard Fine threaded fastener used at the front axle. It secures the track rod protection bracket to the front ...
View full detailsSwivel Recovery Eye Rotating recovery point that bolts through the recovery-point holes in a winch bumper, providing a secure anchor for a shackle ...
View full detailsTransfer Box Flange (Front) is the front output driving flange of the LT230 transfer box - the splined flange onto which the front propshaft bolts....
View full details7 inch high low beam headlight LHD black, with U shape parking light, (PAIR)
Thermostat Housing for the Puma 2.4L TDCi HPCR diesel engine. The cast housing that encloses the engine thermostat and connects the engine block to...
View full detailsSelf Tapping Screw for use in Land Rover body, chassis, and hardware applications.
Dowel Ring locates the cylinder head to the block deck on the 200 TDi and 300 TDi diesel engines. Seated in the block face at the head-to-block jo...
View full detailsThrust Washer is a 1.25mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...
View full detailsRear Door Glass for the rear door aperture, 4mm heated glass. It glazes the rear door opening, seating into the surrounding rubber seal. The heate...
View full detailsHeated Rear Window Switch fitted to the instrument panel facia, this switch activates the heated rear window element, energising the resistive heat...
View full detailsABS Sensor Bush is a retaining bush used to locate the wheel speed sensor within its mounting point in the hub or axle assembly. The bush provides...
View full detailstappet hydraulic Freel. repl.
Chassis Outrigger - Rear for the Defender 110, forming part of the ladder-frame chassis structure at the rear of the vehicle. The rear outrigger i...
View full detailsSealed Rivet for securing fixed side windows. This is a closed-end blind rivet: the sealed body prevents water passing through the rivet hole, keep...
View full detailsDifferential Guard is a galvanised bolt-on steel guard that shields the differential housing on the axle from impact and debris off-road. It clamp...
View full detailsWasher used at front suspension arm pivot points, anti-roll bar stabilizer link connections, and front subframe cross-member fastening interfaces, ...
View full detailsCylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...
View full detailsFlange & Seal Kit for the front output of the LT230 transfer box, fitted to the Defender 90/110 (to 1998), Range Rover Classic (to 1991), and D...
View full detailsDifferential Pan Cover with integral filler plug, for repair of the front differential housing. This weld-in cover replaces the pressed pan sectio...
View full detailsGlow Plug - 300TDi - 24V for the military Defender (Wolf) fitted with the 300TDi 2.5L turbo diesel engine and a 24-volt electrical system. The Wol...
View full detailsGrille & Headlamp Surround Set replaces the front radiator grille and headlamp surrounds with items finished in Santorini Black. The set conta...
View full detailsCrankshaft with Bearings for the 2.25L 4-cylinder petrol engine. The crankshaft converts the reciprocating motion of the pistons into rotational o...
View full detailsKinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...
View full detailsOil Filter Adaptor forms the mounting interface for the spin-on oil filter within the engine oil filter and cooler assembly. Bolted to the cylinde...
View full detailsTailgate Hinge for the drop-side tailgate fitted to the High Capacity Pick Up (HCPU) body variant. This hinge forms the pivoting connection betwee...
View full detailsTow Ball & Pin Hitch Assembly for the towing system, mounting to the rear towing bracket. The assembly combines a tow ball for standard ball-c...
View full detailsPower Steering Pipe Assembly for the steering hydraulic circuit, running between the steering box and the power steering fluid reservoir. It carri...
View full detailsTow Hitch Assembly for the rear towing system, supplied complete with tow ball. It mounts to the rear chassis towing points and provides the coupl...
View full detailsHeater Blower Motor Harness - the wiring harness for the heater (HVAC) blower motor circuit. It carries power and switching between the heater fan...
View full detailsBottom-End Engine Gasket Set for the 2.25L and 2.5L four-cylinder petrol engine. Covers the lower engine assembly gaskets and oil seals for use du...
View full detailsOil Temperature Transmitter for the Defender V8 petrol engine. This sender unit threads into the engine oil gallery and converts oil temperature t...
View full detailsSteering wheel for the steering column assembly within the vehicle steering system. The 48-spline internal hub interfaces directly with the steer...
View full detailsPower Assisted Steering Hose for the 4-cylinder non-Tdi engine, part of the hydraulic steering circuit on right-hand drive Defender 90 and 110 mode...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →