for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Front down pipe LH V8 from vin 267908 to FA 404321
Exhaust Intermediate Pipe connecting the front section of the exhaust system to the silencer on 2.5 Petrol and 2.5 Diesel Naturally Aspirated engin...
View full detailsDoor Latch Link - Rear is the operating link in the rear side door, connecting the outside handle to the door latch. When the exterior handle is o...
View full detailsRear corner wing repair panel for the rear body corner, forming the outer skin where the rear quarter panel wraps round to the rear end panel behin...
View full detailsInjector Bolt for the 2.2L Td4 (Puma) diesel fuel injection system. The bolt retains a fuel injector in its bore in the cylinder head, clamping th...
View full detailsRear Hinge Bracket for the tailgate hinge assembly. The bracket mounts to the rear of the chassis frame and carries the tailgate hinge, locating t...
View full detailsFuel Injector Leak-Off Pipe Kit for the 2.4L Duratorq-TDCi Puma diesel engine, forming part of the fuel injection and return circuit. These leak-o...
View full detailsFuel Tank - 45 Litre for the fuel storage system of the Defender 110. This 45-litre tank fits the standard under-body mounting position on Defende...
View full detailsBonnet Release Cable Assembly, part of the bonnet latch and release mechanism. The cable assembly connects the interior release lever to the bonne...
View full details"DEFENDER" Decal Tape - bonnet name plate lettering supplied as an adhesive decal tape. Applied to the bonnet, forming the "DEFENDER" model name.
"DEFENDER" Decal Tape - bonnet name plate lettering supplied as an adhesive decal tape. Applied to the bonnet, forming the "DEFENDER" model name.
Enhance the protection and safety of your Defender with this front bumper designed for optimal functionality and style. Finished in black, this bum...
View full detailsFootwell Repair Panel for the near-side (N/S) front footwell for 90/110/130 - the pressed floor section at the base of the bulkhead where the occup...
View full detailsWing Top Protector is a workshop protection accessory that lays over the wing top panel during engine-bay maintenance, shielding the paintwork from...
View full detailsIntermediate Exhaust Pipe - stainless steel centre section of the exhaust system, fitted in place of the standard centre silencer between the front...
View full detailsExhaust Link Pipe - Stainless is a centre section for the Td5 exhaust system, fitting in place of the original front silencer. Manufactured in sta...
View full detailsDive into the legendary history of Land Rover with this stunning 3-piece Defender Heritage set. Each 1:76 scale diecast model captures the essence ...
View full detailsRadiator Core is a replacement copper cooling core for the 300 TDi radiator, supplied as the core only without the top and bottom tanks. It is int...
View full detailsWiper Motor Bracket Mounting bracket that locates and supports the windscreen wiper motor. Forms part of the wiper drive assembly, holding the mot...
View full detailsRubber mat set 110 2nd row
Silicone Coolant Hose Kit - a set of replacement hoses for the 200 TDi engine cooling circuit, covering the radiator and associated coolant connect...
View full detailsLower Tailgate for the rear of the body - the drop-down tailboard panel that closes off the rear of the load area. Hinged along its lower edge, it...
View full detailsSpeed Sensor - 3-pin variant for the drivetrain speed sensing circuit. The sensor monitors gearbox or transfer box output shaft rotational speed a...
View full detailsFuel Filter Cover Assembly - front cover for the chassis-mounted fuel filter and sedimentor on diesel engines, including the 200 TDi, 300 TDi and T...
View full detailsWasher is an M12 plain flat washer for use with M12 threaded fasteners. Fitted beneath a bolt head or nut, it provides a flat bearing surface that...
View full detailsCam Cover Washer - plain black washer used on the camshaft cover of the Td5 2.5L 5-cylinder turbo diesel engine. It sits under the fixing that ret...
View full detailsRetaining Clip for the output shaft oil seal on the MT82 6-speed manual gearbox fitted to the Defender from VIN 7A000001 (2007 onwards). This clip...
View full detailsThe Seat Spring Rear Outrigger is a key component designed for the Defender 110/130 models. This high-quality rear seat spring outrigger supports t...
View full detailsFront Radius Arm Mount Bracket forming part of the front suspension mounting on the chassis. The bracket locates on the chassis outrigger section a...
View full detailsFuel Injector Pipe - Cylinder 3 forms part of the high-pressure fuel injection circuit on the 2.5L 200TDi turbo diesel engine. This rigid steel li...
View full detailsFuel Injector Pipe - Cylinder 2 forms part of the high-pressure fuel injection circuit on the 2.5L 200TDi turbo diesel engine. This rigid steel li...
View full detailsLamp Guard Set - Rear - Hinged Hinged rear lamp guard set that protects the rear lamp lenses from stone strike and low-speed impact during off-road...
View full detailsWheel Cylinder Brake - LH
Handbrake Adjuster for the rod-operated transmission parking brake mounted on the LT230 transfer box. On these vehicles the handbrake acts on a dru...
View full detailsFuel Injector Pipe for the high-pressure injection circuit of the 300 TDi 2.5L diesel engine. This rigid steel pipe carries metered high-pressure ...
View full detailsInjector Pipe Kit - set of 4 high-pressure fuel pipes for the 300Tdi 4-cylinder turbo diesel engine, mechanical injection pump variant (Less EDC). ...
View full detailsInjector Pipe - number-one cylinder high-pressure injector pipe for the 2.5L 300 TDi turbo diesel. This rigid steel pipe carries diesel at injecti...
View full detailsDecoke Gasket Set for the 2.25L and 2.5L four-cylinder petrol engine. This is the top-end (cylinder head) gasket set, covering the joints disturbed...
View full detailsPiston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...
View full detailsIgnition Module Link Plug - a 3-to-2 pin adapter plug used with the V8 distributor ignition module. It adapts the wiring connection between a 3-pi...
View full detailsBrake Pipe - rigid hydraulic brake line serving the front-right circuit on ABS-equipped vehicles. It carries pressurised brake fluid through the f...
View full detailsBrake Pipe - rigid hydraulic brake line serving the front-left circuit on ABS-equipped vehicles. It carries pressurised brake fluid through the fr...
View full detailsRear Light Guard Set for Defender models fitted with a rear-door-mounted spare wheel. The set comprises one square guard and one L-shaped guard, f...
View full detailsShaft 90/110 RH 31/10
Contact Set for the Lucas distributor fitted to Land Rover petrol engines, comprising the breaker point assembly within the conventional ignition s...
View full detailsContact Set for the ignition distributor of the 3.5L V8 petrol engine. The contact breaker points open and close the primary circuit to the ignitio...
View full detailsPiston Rings - 200TDi - Standard for the 2.5L 200TDi four-cylinder turbo-diesel engine at standard bore dimensions, for use during engine overhaul....
View full detailsDrop Arm for the steering linkage, fitted to the Gemmer steering box output shaft. The splined eye at the upper end clamps onto the box sector sha...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →