for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Engine Oil Sump for the 2.5L 300 TDi turbo diesel, part of the engine lubrication system. The sump bolts to the underside of the cylinder block an...
View full detailsTiming Pin (Long) is a workshop special tool used to set the engine timing on the Td5 2.5-litre five-cylinder turbo diesel. The pin locks the cran...
View full detailsBulkhead Door Pillar for the right-hand (offside) front door aperture, in the basic configuration. The door pillar forms part of the bulkhead asse...
View full detailsBonnet Under Seal is a rubber sealing strip that fits along the bulkhead drain channel beneath the rear edge of the bonnet, bridging the joint betw...
View full detailsCooler EGR Gasket
Flange Bolt is the special bolt that secures the rear output flange within the manual gearbox output assembly. It clamps the output flange to the ...
View full detailsFuel Pump Cover for the Puma diesel engine. An inspection cover panel fitted to the engine front cover over the mechanical fuel pump drive area. Re...
View full detailsTowing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...
View full detailsA/C Receiver Dryer Assembly for the air conditioning refrigerant circuit. It sits on the high-pressure liquid side, downstream of the condenser and...
View full detailsLow Ratio Detection Switch - the transfer box range-detection switch, mounted on the front housing of the transfer box. It senses whether the tran...
View full detailsSeat Cushion Cover - Base in Techno-pattern velour fabric, for the squab section of the front seat on Defender 90, 110, and 130 models. The Techno...
View full detailsClutch Release Fork is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch slave cylinder ...
View full detailsFront Axle Drive Shaft Spacer for the front hub and stub axle assembly. The spacer fits over the front drive shaft and sets the axial position of ...
View full detailsThrust Washer for the differential assembly within the LT230 transfer box. This 1.35mm thrust washer sits within the LT230 centre differential, co...
View full detailsRear Propeller Shaft for 4-cylinder models, with a collapsed (compressed) length of 64cm. It transmits drive from the transfer box rear output to ...
View full detailsSynchro Hub is part of the synchromesh assembly in the LT76 gearbox, splined to the mainshaft and carrying the sliding sleeve that engages the gear...
View full detailsGasket
Clutch Release Arm Pivot Plate for the LT77 5-speed manual gearbox. Mounts inside the clutch bellhousing and provides the pivot point for the clut...
View full detailsSpeedometer Drive Gear in the drivetrain. This gear drives the speedometer cable via the gearbox or transfer case output, translating shaft rotati...
View full detailsRear Axle Half Shaft - right-hand, 10/24 spline, for the Series III rear axle. This shaft transmits drive from the rear differential to the rear wh...
View full detailsPiston for the 2.5L four-cylinder turbo-diesel engine, operating within the cylinder block as part of the piston and connecting-rod assembly. The ...
View full detailsExhaust Valve for the 2.25L 4-Cylinder Petrol engine, fitted in the cylinder head valvetrain assembly. This valve operates in the cylinder head to...
View full detailsPower Steering Pump Pulley for the power steering hydraulic circuit. The pulley mounts on the power steering pump shaft and is driven by the auxil...
View full detailsPiston Cooling Oil Jet Relief Valve - part of the engine lubrication system, fitted in the cylinder block oil feed to the piston cooling jets. It r...
View full detailsValve Cotter in the cylinder head valvetrain, locking the valve spring retainer to the valve stem. The cotters seat as a pair into the machined gr...
View full detailsInlet Valve for the cylinder head valve train, with a 34.5 mm head diameter. The inlet valve opens on the induction stroke to admit the air/fuel c...
View full detailsRadiator assembly
Hose Clip is a worm-drive (Jubilee-type) clamp with a 20-30 mm clamping range. Tightened by a captive worm screw, it secures a flexible hose onto ...
View full detailsBracket
Upper Radiator Mounting Bracket that locates and secures the top of the radiator in the cooling system. Fitted to four-cylinder TDi and Td5 applic...
View full detailsIntercooler Hose - 300TDi
Centre Silencer for the exhaust system on the Defender 90 with 300TDi engine. Fitted in the mid-section of the exhaust run between the downpipe an...
View full detailsFront Exhaust Pipe for the Defender equipped with the naturally-aspirated 2.5L diesel engine. This downpipe connects the exhaust manifold outlet t...
View full detailsOil Cooler Adaptor Gasket for the Rover V8 petrol engine, part of the engine lubrication circuit. It seals the joint between the oil cooler adapto...
View full detailsInlet Valve for the TD5 2.5L 5-Cylinder Turbo Diesel engine, as fitted to the Defender and Discovery 2. The inlet valve controls the intake charge...
View full detailsCylinder Head Gasket for the 2.5L 200TDi and 300TDi diesel engines, supplied in the 1.3mm compressed-thickness grade (identified by a single hole)....
View full detailsTurbocharger for the forced-induction system of the 2.5L 300 TDi diesel engine, supplied complete with the mid manifold section. Driven by exhaust...
View full detailsTappet Adjusting Screw for the 2.5L 300 TDi turbocharged diesel engine, fitted in the rocker arm of the valvetrain. Threaded into the rocker arm t...
View full detailsPower Steering & ACE Pump Pulley mounts to the hydraulic pump drive shaft and is turned by the engine's auxiliary drive belt. Drives the power...
View full detailsRocker Shaft Stud - 300TDi is a cylinder head stud used in the rocker shaft assembly of the 300TDi 2.5L 4-cylinder turbo diesel engine. The stud t...
View full detailsSound Deadening Pad is an acoustic pad fitted to the rocker cover on the 2.5L 300TDi turbo diesel engine. It damps mechanical noise radiating from...
View full detailsOil Dipstick Tube, V8
Stepper Motor for the V8 EFI petrol engine, part of the idle air control system on the intake plenum. Acts as the idle air control valve, metering...
View full detailsViscous Fan Coupling drives the engine cooling fan on the 3.9L and 4.0L V8 EFI petrol engine. The temperature-sensitive coupling varies fan speed ...
View full detailsEngine Piston for the 2.5L 300 TDi diesel engine, supplied in standard bore size. The piston runs in the cylinder bore and transfers combustion pr...
View full detailsOil Pump - 200Tdi is the engine-driven pump responsible for circulating pressurised oil throughout the lubrication system of the 200Tdi 2.5L direct...
View full detailsInlet Valve for the cylinder head valvetrain of the 200TDi 2.5L 4-cylinder turbo diesel engine. The valve seals against its seat in the cylinder h...
View full detailsCamshaft Pulley O-Ring - the seal fitted at the camshaft pulley on the front timing drive. It seals the joint between the camshaft nose and its dr...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →