for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Engine Cover - 2.4 Diesel
Con Rod Bearing Set for the 2.5L 4-cylinder engine, supplied in 0.010" undersize. These are the big-end shell bearings that sit between the cranks...
View full detailsPiston Assembly for the Land Rover 3.5-litre all-aluminium V8 petrol engine. Forms part of the reciprocating assembly within the engine cylinder bo...
View full detailsFuse Box Cover - Facia is the moulded cover that closes off the facia-mounted fuse box, concealing the fuse and relay positions behind the dash. I...
View full detailsMain Bearing Set - 0.020in Undersize - crankshaft main bearing shells for the 3.5 and 3.9 litre V8 petrol engine, sized for a crankshaft that has b...
View full detailsFuel Tank Vent Hose - Puma TDCi
Fuel Tank Filler Hose - moulded connecting hose from the fuel tank filler assembly. It joins the filler neck at the body aperture to the inlet spi...
View full detailsRear Shock Absorber - Heavy Duty - hydraulic telescopic damper for the rear coil-sprung suspension, mounted between the axle bracket and the chassi...
View full detailsDoor Glass Channel for the front door, upper section. This channel runs along the top of the front door frame and guides and seals the window glas...
View full detailsCrankcase Ventilation Valve located in the engine air cleaner assembly. It controls the flow of crankcase blow-by gases from the breather system i...
View full detailsDamper Mounting Bush - Polyurethane - Lower - polyurethane isolating bush for the lower shock absorber mounting. The bush sits between the damper ...
View full detailsHeadlamp Finisher is the right-hand headlamp surround trim on the front wing. It frames the headlamp aperture of the front wing assembly, finishin...
View full detailsHeadlamp Finisher is the left-hand headlamp surround trim on the front wing. It frames the headlamp aperture of the front wing assembly, finishing...
View full detailsRear Road Coil Spring, driver's side. It locates between the rear axle spring seat and the chassis spring turret and carries the static and dynamic...
View full detailsRear Road Coil Spring, passenger side. It locates between the rear axle spring seat and the chassis spring turret and carries the static and dynami...
View full detailsDoor Check Arm Pivot Bracket for the right-hand front door. This bracket anchors the door check arm to the body pillar and forms the pivot point f...
View full detailsDoor Check Arm Pivot Bracket for the left-hand front door. This bracket anchors the door check arm to the body pillar and forms the pivot point fo...
View full detailsScrew - self-tapping screw from the Radiator and Hoses assembly of the cooling system. It cuts its own thread as it is driven, retaining the radia...
View full detailsBleed Screw in red anodised aluminium, fitted at the bleed point of the radiator hose circuit on the Td5 2.5L 5-Cylinder Turbo Diesel. The screw c...
View full detailsHose Clip for small-bore hoses in the engine bay. On the Td5 2.5L five-cylinder turbo diesel it retains the cam cover breather valve hose, keeping...
View full detailsIgnition coil for the distributor ignition system on V8 petrol engines. Steps the low-tension supply up to the high-tension voltage required at th...
View full detailsNumber Plate Plinth - rear registration plate plinth, part of the rear body exterior fittings. It mounts to the rear body panel and provides the f...
View full detailsBrake Disc Splash Shield - Rear - RH - Galv is the right-hand rear brake disc splash shield, the backing plate mounted behind the disc on the rear ...
View full detailsBrake Disc Splash Shield - Rear - LH - Galv is the left-hand rear brake disc splash shield, the backing plate mounted behind the disc on the rear a...
View full detailsTransfer Box Oil Seal Shield for the front output flange of the LT230 transfer box. The shield sits over the output flange ahead of the oil seal a...
View full detailsAuxiliary Drive Belt for the 300Tdi 2.5L direct injection turbo diesel engine. Driven from the crankshaft pulley, the belt runs a single serpentin...
View full detailsPanhard Rod Bush - Front is a yellow polyurethane bush for the front panhard rod. The panhard rod is the transverse link that locates the front ax...
View full detailsIn-tank fuel pump for the auxiliary fuel tank installation, part of the fuel delivery system. Mounts inside the auxiliary tank and lifts fuel from...
View full detailsRear Step Assembly - the production-fit folding step mounted at the rear of the vehicle, below the rear door. The step provides footing for access...
View full detailsSeal Ring - sealing ring for the turbocharger elbow joint in the engine induction system. The ring seals the connection between the turbocharger e...
View full detailsHeater hose forming part of the heater coolant circuit within the engine cooling system. The hose runs between the coolant take-off at the inlet m...
View full detailsClutch Slave Cylinder is the hydraulic actuator in the clutch release mechanism. It receives pressure from the clutch master cylinder and applies ...
View full detailsSwivel Housing Repair Kit for the front axle swivel assembly. Supplied for one side. The swivel housing sits at the outer end of the front axle ca...
View full detailsFront Seat Covers - a tailored waterproof cover set for the pair of front seats, in grey. The covers are made from waterproof woven polyester with...
View full detailsBush Kit - Front - From VIN 2A626646
Transfer Box
Rear Door Casing - the interior trim panel that lines the inner face of the rear end door. It covers the door's inner structure to give a finished...
View full detailsCentre Cubby Box - Techno finish. A console box that mounts on the transmission tunnel between the front seats, providing enclosed central storage ...
View full detailsKey blank for the door lock barrels and the cubby box barrel lock. Supplied uncut - the blade carries the correct key section for these barrels, bu...
View full detailsRear Shock Absorber - hydraulic damper for the rear suspension of the short-wheelbase (90-inch) chassis. It controls the oscillation of the rear co...
View full detailsCoil Spring is a heavy-duty rear suspension coil spring that raises ride height by approximately 40mm (1.5 inch) over standard. It is rated to car...
View full detailsFront Wheel Bearing Kit containing the parts needed to overhaul one front hub bearing assembly. The taper roller bearings carry the front hub on th...
View full detailsHose - Connecting
Hex Nut - narrow-pattern hexagon nut used in the steering linkage, at the track rod and steering damper fixings. Two are used per vehicle. Steerin...
View full detailsDifferential Gear Kit for the LT230 transfer box centre differential. The centre differential splits drive between the front and rear output shaft...
View full detailsHandbrake cable from the handbrake actuation assembly, linking the handbrake lever to the transmission brake mounted on the transfer box rear outpu...
View full detailsRear Seat Frame Fastener - retaining fastener for the rear seat frame mounting in the load area. Secures the rear row seat frame assembly to its b...
View full detailsGrille Mounting Bracket Kit in stainless steel for the front radiator grille panel, covering the air conditioning front panel bracket positions. T...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →