for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Bleed screw for the coolant vent hose in the engine cooling system. Threads into the vent point on the heater outlet hose at the coolant expansion...
View full detailsHeater water inlet hose for the 2.4 Td4 diesel engine, forming part of the heater circuit within the engine cooling system. Delivers heated coolan...
View full detailsHeater outlet hose for the 2.5L Td5 five-cylinder turbo diesel, forming part of the heater circuit within the engine cooling system. Returns coola...
View full detailsHeater water inlet hose forming part of the heater circuit within the engine cooling system. Carries coolant from the engine feed to the heater ma...
View full detailsCross Rod Eye End for the steering linkage, left-hand-drive applications. This eye end fits to the steering cross rod (track rod) and provides the...
View full detailsElectronic Ignition Kit for the Rover V8 petrol engine with a points-type distributor. The kit replaces the mechanical contact points and condenser...
View full detailsSteel Wheel - 16 x 6.5 is a pressed-steel tubeless road wheel finished in black. Technical data: Size: 16 x 6.5 PCD: 5 x 165.1 mm Offset: ET20 ...
View full detailsWater Pump for the 2.4L Duratorq TDCi (Puma) diesel engine, forming part of the engine cooling circuit. Driven from the auxiliary belt, the pump c...
View full detailsIntercooler Hose is part of the charge-air cooling circuit, connecting the intercooler to the adjoining charge-air tube. It carries pressurised, c...
View full detailsRetrim Kit - Black - Outer Seat - No Adhesive
Retrim Kit - Black - Outer Seat - With Adhesive
Gudgeon Pin Bush - the small-end bush pressed into the connecting rod for the gudgeon pin. It forms the bearing surface between the gudgeon (pisto...
View full detailsDashboard Assembly Plate is a structural panel within the facia assembly, forming the mounting base onto which the instrument panel and dashboard t...
View full detailsBench Seat Backrest in techno fabric, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts t...
View full detailsBench Seat Backrest in black vinyl, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts to ...
View full detailsSeat Retaining Strap Assembly for the rear inward-facing individual seat. The strap attaches the seat assembly to its mounting point and retains t...
View full detailsCaliper Repair Kit for overhauling the front brake callipers. The kit contains stainless steel replacement pistons, the calliper seal repair kit an...
View full detailsGear Selector Bush for the LT230 transfer box high/low gear change mechanism. The bush seats in the gear change housing and carries the high/low s...
View full detailsHeavy Duty Drive Member Kit - Defender to KA
EGR Blanking & Silicone Hose Kit disables the exhaust gas recirculation (EGR) function on the Td5 engine, blanking off the recirculation of exh...
View full detailsCrown Wheel & Pinion - the final drive gear pair for the Rover-type differential, 10-spline pinion, as used in the two-pinion differential cent...
View full detailsTurbocharger Oil Feed Pipe - carries pressurised engine oil from the cylinder block to the turbocharger bearing housing, lubricating and cooling th...
View full detailsAlternator, A127L type with 100 A output, for the charging system of the 300 TDi diesel engine. Belt-driven from the crankshaft accessory drive, t...
View full detailsPiston Assembly - Eng
Front Outer Seat Re-Trim Kit - a complete re-covering set for one outer front seat in the XS black mesh trim, renewing both the foam and the trim c...
View full detailsRear Coil Springs supplied as a pair, giving a raised ride height of +50mm at a medium-duty spring rate. The springs lift the rear of the vehicle ...
View full detailsFront Cylinder Cover encloses the front of the cylinder block on the 2.2L turbo-diesel (Puma) engine, sealing the front timing drive area. It carr...
View full detailsFuel Tank Cradle supports and locates the fuel tank against the chassis. The cradle carries the weight of the tank and clamps it to the chassis mo...
View full detailsRear Door Card is the interior trim panel that finishes the inside face of the rear tail door, concealing the door structure behind a moulded casin...
View full detailsSilicone Coolant Hose Kit - a five-piece silicone hose set that replaces the main radiator and coolant-system hoses on the 2.4L TDCi (Puma) diesel ...
View full detailsOil Pump for the 2.4L Duratorq TDCi diesel engine. It draws oil from the sump and delivers it under pressure to the engine lubrication circuit, fe...
View full detailsRear Body Capping for the Defender rear body, in galvanised steel. It caps and protects the top edge of the rear body panel and is galvanised for ...
View full detailsFinisher
Mesh Dog Guard a partition panel that mounts against the full-height rear bulkhead to separate the cab from the load area. Fitted to the existing ...
View full detailsTop Radiator Hose forming part of the engine cooling circuit. It connects the engine coolant outlet to the top of the radiator, carrying hot coola...
View full detailsDog Guard - 90/110
Fuel Pipe - twin-line pump-to-engine section of the fuel delivery circuit on the 2.5L Td5 five-cylinder turbo diesel. The two lines are routed tog...
View full detailsFuel Supply Manifold Sensor - the rail pressure sensor of the HPCR common-rail fuel injection system on the 2.4L Duratorq TDCi four-cylinder diesel...
View full detailsRubber Floor Mat for the 5-seat cabin floor. Moulded rubber mat shaped to the vehicle floor contour, protecting the original floor covering agains...
View full detailsClutch Repair Kit - V8
Heavy Duty Drive Member Kit - Defender - Discovery 1 - RRC
Piston Assembly for the Td5 2.5L 5-Cylinder Turbo Diesel, part of the cranktrain within the cylinder block assembly. Oversize service piston, for u...
View full detailsMass Air Flow (MAF) Sensor mounted in the air intake tract, downstream of the air cleaner. It measures the mass of air drawn into the engine and s...
View full detailsWheel Arch Extension Kit is a matched pair of rear wheel arch extensions that widen arch coverage by 30 mm, giving clearance for wider tyres or whe...
View full detailsFuel Vapour Valve fitted to the fuel tank as part of the evaporative emissions and tank ventilation system. It vents fuel vapour from the tank to ...
View full detailsClutch Kit for the 200 TDi and 300 TDi diesel engines, uprated to a heavy-duty specification. The clutch transmits drive from the engine to the ge...
View full detailsClutch Kit for the 200 TDi and 300 TDi diesel engines, uprated to a heavy-duty specification. The clutch transmits drive from the engine to the ge...
View full detailsFuel Tank Cradle supports and locates the fuel tank against the chassis. The cradle carries the weight of the tank and clamps it to the chassis mo...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →