for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Transfer Box Flange & Rebuild Kit - an overhaul kit for the LT230 transfer box, the two-speed transfer case that splits drive from the gearbox ...
View full detailsFuel Tank is the main fuel reservoir in the fuel storage and supply assembly. This is the early external-pump specification: the tank carries no i...
View full detailsBulkhead Repair Kit - bodyshell repair panels. The bulkhead is the structural panel separating the engine bay from the cabin, carrying the footwel...
View full detailsCentre Console Switch Pack moulding in black, forming part of the centre console trim. This panel mounts in the centre console and provides the ap...
View full detailsCrown Wheel and Pinion is the final-drive gear set inside the differential, comprising the ring (crown) gear and its matched drive pinion. The pin...
View full detailsRear Crossmember - Short Extensions - replacement rear chassis crossmember, supplied with short extensions, forming the rearmost structural section...
View full detailsDog Guard - full-height mesh guard for the rear load area. It forms a barrier between the load space and the occupant area, keeping animals in the...
View full detailsFront Bumper is a military/Wolf-style front bumper supplied complete with a centre recovery pin (pintle). The kit comprises the front bumper (DPB0...
View full detailsOil Filter Adaptor mounts the oil filter to the engine block within the lubrication circuit of the 2.2 Td4 diesel engine. It seats between the blo...
View full detailsSteel Wheel - 16 x 8 inch pressed steel road wheel in the large-offset one-tonne style, supplied in black primer ready for finishing. The offset i...
View full detailsCountershaft Gear for the LT230 transfer box, mounted on the intermediate shaft. The gear runs on the intermediate shaft between the transfer box ...
View full detailsCentre Exhaust Silencer for the 110" wheelbase, fitted in the intermediate section of the exhaust system between the front pipe and the rear silenc...
View full detailsCrownwheel and Pinion Set - 3.54:1 final drive ratio (13-tooth pinion, 46-tooth crownwheel), for the two-pinion differential used in the Land Rover...
View full detailsRadiator for the 200 TDi / 300 TDi diesel engine cooling system. The main heat exchanger that transfers heat from the coolant to the passing airfl...
View full detailsTailboard Assembly, lower hinged. The drop-down rear panel that closes the rear of the load area. Hinged along its lower edge, it swings down to h...
View full detailsFront Door Hinge Set - Aluminium - replacement hinges forming the pivot between the front row doors and the A-post. The original hinge castings co...
View full detailsEGR Cooler for the exhaust gas recirculation system. It uses engine coolant to lower the temperature of recirculated exhaust gas before it re-enter...
View full detailsSuspension Kit - a standard ride-height, heavy-duty coil spring and shock absorber set covering both the front and rear axles. The kit contains he...
View full detailsAir Intake Hose for the air cleaner system, ducting filtered intake air between the air cleaner housing and the engine. The hose carries air drawn...
View full detailsDoor Hinge Pin Kit - Stainless Steel - renewal hardware for the door hinge pivots. The hinge pin is the wearing part of a door hinge: as the pin a...
View full detailsSupport
Camshaft Cover for the 2.2L Puma diesel engine, enclosing the camshafts and valve train at the top of the cylinder head. The cover encloses the ov...
View full detailsRear Window Glass for the rear side body aperture, supplied as the glass panel alone - without the surrounding window frame (surround). Replaces a...
View full detailsMulti-Function Switch is the combined steering-column stalk switch cluster. Mounted on the steering column, it integrates the exterior lighting, d...
View full detailsTowing Attachment Assembly - adjustable-height towing attachment that bolts to the rear of the chassis and forms the mounting interface between the...
View full detailsChequer Plate Kit - a black satin aluminium chequer plate set for exterior body protection. The kit covers the bonnet, wing tops, sills and rear c...
View full detailsCatalytic Converter for the V8 petrol exhaust system. It treats exhaust gases to reduce emissions, fitted in the exhaust line on applications equi...
View full detailsAlloy Wheel - Sawtooth-pattern road wheel measuring 18 inch diameter by 8J rim width, with an ET20 offset and a 5 x 165 mm PCD stud pattern. Gloss ...
View full detailsSeat Frame - front seat base frame for the right-hand seat. The frame forms the structural base of the front seat, carrying the seat cushion and p...
View full detailsKnock Sensor is part of the engine management system on the V8 petrol engine. Mounted to the cylinder block, it detects combustion knock (detonati...
View full detailsRear Body Carpet Set for the load area of the Defender 90, in the configuration with forward-facing rear seats and cut-away wheel arches. The set ...
View full detailsCarpet Set with Inward Facing SE
Rear Body Carpet Set for the load area of the Defender 90 van-back body, in the configuration without rear seats and with square wheel arches. The...
View full detailsDifferential Case - the rotating carrier at the centre of the front axle differential assembly. The crown wheel bolts to the case, and the case in...
View full detailsABS Ring - the rear reluctor (exciter) ring in the anti-lock braking system. Mounted at the rear, it is the toothed ring the wheel speed sensor re...
View full detailsWheel Spacers - Set of 4 - spacers that fit between the hub and wheel to increase track width, improving stance and clearing larger tyres or brake ...
View full detailsAlloy Wheel - road wheel measuring 18 inch diameter by 8J rim width, with an ET20 offset and a 5 x 165 mm PCD stud pattern, finished in silver. Th...
View full detailsFront Winch Bumper replacing the standard front bumper and carrying the winch within the bumper structure. The bumper bolts to the chassis front d...
View full detailsTiming Chain Kit for the 2.4L Puma diesel engine, supplied complete with sprockets. The kit renews the timing drive at the front of the engine, wh...
View full detailsDistributor for the ignition system of the 3.5L V8 twin-carburettor petrol engine. The distributor is driven from the camshaft and routes high-ten...
View full detailsAdjustable-Height Towing Bar a rear towing attachment that bolts to the chassis towing points and carries the tow ball or coupling. The drop plate...
View full detailsRadiator Assembly - the main heat exchanger of the engine cooling system, mounted in the front panel behind the grille. Coolant leaving the cylind...
View full detailsSliding Window Kit - Deluxe, supplied as a pair for the rear body sides. The kit fits a horizontally sliding glass window into the rear side panel...
View full detailsAlloy Wheel - road wheel measuring 16 inch diameter by 7J rim width, with an ET20 offset and a 5 x 165 mm PCD stud pattern. Gloss black finish with...
View full detailsWinch Bumper is a heavy-duty steel replacement front bumper with an integral winch mounting, allowing a winch to be carried at the front of the veh...
View full detailsBush - 3 Degree Ultra Light Rad Arm Wide Pair - Defender - Discovery 1 - RRC
Sidestep - Defender (Pair)
Rock Sliders mount along the sills to protect the lower bodywork and chassis from rocks and obstacles during off-road use, and give a bearing point...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →