for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Interior door locking peg, part of the door lock linkage. The peg screws onto the top of the door lock rod and is lifted or pushed by hand to lock ...
View full detailsFront seat squab cover for the seat back of the front seat assembly. The cover fits over the seat back foam and frame and is retained around the s...
View full detailsRear Stub Axle Kit for the Salisbury rear axle. One kit covers a single rear corner. The stub axle bolts to the end of the axle case and forms the...
View full detailsRear Mud Flap Bracket in stainless steel. This bracket mounts the rear mud flap to the vehicle, holding it in position behind the rear wheel. Made...
View full detailsFuel Tank Guard - underbody protection panel for the fuel tank, part of the chassis and underbody protection group. Formed from 6 mm aluminium, th...
View full detailsTurret Securing Ring for the front shock absorber turret, supplied as a pair. The rings clamp the turret to its mounting in the front suspension. ...
View full detailsClutch Kit for the Td5 2.5L 5-cylinder turbo diesel, covering the clutch assembly between the engine and the manual gearbox. The driven plate runs...
View full detailsH D Steering Rods - Defender
Front Suspension Bolt Kit - Defender
Front Shock Absorber fits in the front suspension, damping spring oscillation and axle movement to keep the tyres in contact with the road surface....
View full detailsHeater Control Knob - anodised aluminium replacement knob for the heater control levers in the heating and ventilation control assembly on the cent...
View full detailsAlloy Intake Pipe Kit for the induction system of the Td5 2.5L 5-cylinder turbo diesel, replacing the moulded intake ducting between the air flow m...
View full detailsFront seat squab cover in Techno trim, with an integral map pocket in the rear face. The squab cover fits over the seat back foam and frame and is...
View full detailsAlternator upgrade kit for the 200Tdi 2.5L 4-cylinder turbo diesel, replacing the standard alternator in the engine charging circuit with a higher-...
View full detailsDouble DIN Fascia - Piano Black - a replacement centre dash panel that converts the factory single-aperture opening to accept a double DIN head uni...
View full detailsCubby Box - centre console stowage box for the transmission tunnel area between the front seats. The box mounts on the tunnel in the centre seat p...
View full detailsCubby Box - Black Mesh - a centre floor console that mounts between the front seats, giving an enclosed storage compartment with a padded lid that ...
View full detailsHeavy Duty Rear Spring - Defender 110 130
Rear Seat Assembly - full-width rear bench seat for the long-wheelbase rear load area. This is the elongated 1,200 mm bench pattern, mounted trans...
View full detailsFuel Cooler Guard - protective guard for the underbody-mounted fuel cooler in the fuel return circuit. The fuel cooler sits low on the underbody w...
View full detailsWindow Channel Kit - front right-hand door, part of the door glass and window regulator assembly. The channelling guides the door glass as it is r...
View full detailsFront Suspension Bolt Kit From - Defender
Gearbox Bearing Kit for the R380 five-speed manual gearbox, suffix K onwards. Used when overhauling the gearbox. The bearings locate and support t...
View full details200 TDi Type Engine Alternator - Discovery
Dog Guard in mesh, fitted behind the second row of seats to separate the load area from the passenger compartment. The guard mounts to the body an...
View full detailsInjector Washer Kit for the Td5 2.5L 5-cylinder turbo diesel - fuel injection system, injector-to-cylinder-head sealing. Each injector seals into ...
View full detailsBrake Calliper Piston and Seal Kit - Front Axle - overhaul set for the front brake callipers, part of the front foundation braking assembly. Each ...
View full detailsHigh-Top Centre Cubby Box in grey. A Defender-style console box that mounts on the transmission tunnel between the front seats, providing enclosed ...
View full detailsCam Cover Gasket Set for the 2.4L TDCi (Puma) diesel engine, covering the camshaft cover and injector sealing joints. The camshaft cover seals the...
View full detailsSwivel Pin Kit - Fits Defender to KA930455
Set - 110 SW Rear Body Carpet with
Timing Belt Kit Dis - RRC 200TDi
Poly Bush Kit A complete-vehicle set of polyurethane suspension bushes that replace the original rubber bushes throughout the chassis and suspensio...
View full detailsStub Axle Kit Front - Defender Up to KA
Stub Axle Kit Rear - Defender to KA
Cylinder Head Set for the Td5 2.5L 5-cylinder turbo diesel - the gaskets and seals disturbed when the cylinder head is removed and refitted. Suppl...
View full detailsFront Suspension Bolt Kit LA930 - Defender
Double DIN Fascia - Matt Black - a replacement centre dash panel that converts the factory single-aperture opening to accept a double DIN head unit...
View full detailsRear Inward-Facing Seat for the load area, finished in Twill trim. This is a complete inward-facing bench seat assembly that mounts along the side ...
View full detailsSeat Back Cover in grey vinyl, for the front outer seat backrest - driver or outer passenger side. Replaces the worn or damaged trim cover on the ...
View full detailsStub Axle Kit - front stub axle with its sealing and fixing parts for one corner. The stub axle bolts to the outer face of the swivel housing and f...
View full detailsRear Suspension - Defender
Head Bolt Set - cylinder head fixings for the 2.5L Td5 five-cylinder turbo diesel engine. The bolts clamp the cylinder head to the block, compress...
View full detailsService Kit for the 2.5L 200TDi diesel engine, supplied complete with the engine oil for a scheduled service. Provides the filters and service com...
View full details7 Inch Round LED Headlamp for the front lighting system, replacing the conventional 7-inch round sealed-beam or halogen headlamp. The LED light so...
View full detailsRear Suspension Bolt Kit - Defender
Lamp guard for 95 mm round NAS-pattern rear lamps, shielding the lens and lamp body against impact from branches, stones and loaded cargo. Moulded...
View full detailsRear wheel arch protectors, supplied as a pair, fitting behind the rear wheel as part of the body protection and splash-guard arrangement. They cl...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →