for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Firtree Clip - a push-in fastener with a ribbed, fir-tree profile that grips into a pre-drilled panel hole. Used to secure trim panels, wiring loo...
View full detailsTailgate Bracket for the rear tailgate. This bracket mounts to the rear body and supports the tailgate, providing a fixing point on High Capacity ...
View full detailsBolt for the engine front cover. Hexagon-head threaded fastener securing the timing front cover on the V8 petrol engine. Supplied individually.
Bracket
Door Check Arm Bracket anchors the rear side door check strap to the door assembly. The check strap limits how far the door swings open and holds ...
View full detailsInner Door Panel Assembly forms the inner structural panel of the door. This panel makes up the inner face of the door, providing the mounting str...
View full detailsBall Joint Repair Kit - Outer
Bracket
Headlamp Assembly - a complete halogen headlamp unit for the front lighting. Supplied with the right-hand-drive beam pattern, and without the wiri...
View full detailsAlternator Bearing for the vehicle charging system. This bearing supports the alternator rotor shaft, allowing it to spin freely within the altern...
View full detailsBody Panel Stud is a threaded fixing used in the cab and rear body panel mounting hardware. It provides a fixed anchor point for securing body pan...
View full detailsHeater Hose is a coolant hose in the heater circuit of the Td5 2.5L 5-cylinder turbo diesel. It carries engine coolant between the cooling system ...
View full detailsSeat Squab is the backrest section of the right-hand front seat assembly. The squab forms the upright cushion against which the occupant's back re...
View full detailsBonnet Stay Bracket is the left-hand mounting bracket for the bonnet stay. It forms the pivot-bush end of the bonnet stay assembly, providing the ...
View full detailsBonnet Stay Bracket - mounting bracket for the bonnet stay. Locates and supports the bonnet stay, holding the bonnet in the open position for engi...
View full detailsBulkhead Vent - Open - LH - the left-hand (near side) hinged vent lid set into the bulkhead, forming part of the fresh-air ventilation system. Whe...
View full detailsBulkhead Vent - Open - RH - the right-hand (off side) hinged vent lid set into the bulkhead, forming part of the fresh-air ventilation system. Whe...
View full detailsBrake Pipe
Instrument Cover is the trim cover for the instrument pack within the facia assembly, enclosing the main gauge cluster. It is also used as the cov...
View full detailsPanhard Rod Bush Set is a set of polyurethane bushes for the Panhard rod mountings. The Panhard rod locates the axle laterally relative to the cha...
View full detailsSteel Road Wheel - Wolf Style is a heavy-duty steel road wheel finished in silver, styled after the Wolf pattern. It provides a durable steel rim ...
View full detailsBump Stop - Yellow
Bump Stop - Rear Radius Arm is a polyurethane compression bump stop for the rear suspension, mounted at the radius arm. It limits axle travel at f...
View full detailsBush Set - Rear Upper Link is a polyurethane bush set for the rear suspension upper link, sized for the M16 link fixing. The bushes locate the upp...
View full detailsGearbox Crossmember - the gearbox mounting crossmember section of the chassis frame. This welded steel crossmember spans the two chassis rails at ...
View full detailsSpring Isolator seats between the coil spring and its mounting platform in the suspension. It cushions the contact between the spring end and the ...
View full detailsWiper Motor Grommet for the rear screen wiper assembly. It seals the aperture in the rear door or tailgate where the wiper motor spindle passes thr...
View full detailsBody Finisher - a rear body capping fitted along the upper edge of the rear body, providing a finished trim edge over the panel seam. The capping ...
View full detailsAlternator for the V8 EFI petrol charging system, rated at 100A. This is the A127-type alternator assembly, belt-driven from the crankshaft pulley ...
View full detailsBody Finisher - a rear body capping fitted along the upper edge of the rear body, providing a finished trim edge over the panel seam. The capping ...
View full detailsBonnet Release Cable, part of the bonnet latch and release mechanism. The cable connects the interior release lever to the bonnet lock, transmitti...
View full detailsHard Top Side Window Seal. It seals the fixed side window of the hard top to the body aperture, sealing against water ingress and wind noise.
Seat Base Locker Lid - Right Hand. This is the hinged lid that closes the stowage locker built into the seat base, providing access to the storage ...
View full detailsInterior Facia Washer used in the dashboard and facia assembly. The washer distributes the load of a fixing across trim and facia components durin...
View full detailsCamshaft Bearing Kit
Camshaft Bearing Kit
Differential Shim for the Salisbury rear differential, fitted within the differential bearing assembly. The shim sets bearing preload and crown wh...
View full detailsDifferential Shim for the Salisbury rear differential, fitted within the differential bearing assembly. The shim sets bearing preload and crown wh...
View full detailsPolyurethane Bush Set in yellow, supplied for suspension mounting points that use a rubber-style bush. Supplied as a set of yellow polyurethane bu...
View full detailsWasher used within the ignition system of four-cylinder petrol engines, associated with the distributor, ignition coil, HT leads and spark plug ins...
View full detailsCable Tie is a harness fixing used to bundle and route wiring looms, hoses and cables against the chassis and body. It secures the harness in posi...
View full detailsA-Frame Crossmember is the rear chassis crossmember that carries the A-frame ball-joint mount, anchoring the top link that locates the rear axle la...
View full detailsRear Wing Protector in aluminium chequer plate, guarding the rear wing top and corner - one of the most exposed panels on the body. Fits over the ...
View full detailsChequered Sills 90 - Pair
Brushed Stainless Steel Door Thresher E
HD Rear Bumper
Door Hinge Kit - Front - front door hinge and pin set with fixings, forming part of the door mounting hardware. Each hinge bolts to the body pilla...
View full detailsRear Axle Half Shaft - RH, Heavy Duty, part of the disc-braked Salisbury rear axle assembly. The right-hand halfshaft transmits drive from the dif...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →