for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Layshaft Roller Bearing for the LT85 five-speed manual gearbox, fitted at the front of the layshaft. The layshaft (also known as the countershaft)...
View full detailsPrimary Pinion is the input gear of the LT77 five-speed manual gearbox. Mounted on the primary (input) shaft, it takes drive from the clutch into ...
View full detailsFront Bumper - Military Style A heavy-duty steel front bumper finished in black, styled on the military-specification Defender bumper. It replaces ...
View full detailsWading Kit for the drivetrain and engine breather system, extending the breather points of the axles, gearbox and engine to a higher level. Raisin...
View full detailsBulkhead - the structural firewall panel that separates the engine compartment from the cabin. It forms the forward mounting face for the pedal box...
View full detailsAlternator Capacitor - a radio-frequency suppression capacitor fitted to the vehicle charging circuit. It mounts at the alternator output terminal....
View full detailsTensioner Pulley Bearing for the auxiliary drive belt system on air-conditioned vehicles. It is the bearing carried within the idler/tensioner pul...
View full detailsGlow Plug Lead for the pre-heat (glow plug) circuit of the 200 TDi and 300 TDi diesel engines. It interconnects the glow plugs and carries the sup...
View full detailsExhaust Gas Temperature Sensor - post-catalyst temperature sensor in the exhaust after-treatment system, mounted downstream of the catalytic conver...
View full detailsSteel Ball for the timing chain tensioner, 7/32 in diameter. Seats within the tensioner mechanism to help maintain correct timing chain tension.
Gasket
Gearchange Lever Pin is a pivot pin in the manual gearbox gear change mechanism. It locates and retains the gear change lever, allowing it to pivo...
View full detailsFront Door Glass is the fixed clear glazing panel for the left-hand front door, forming part of the door assembly. This is the left-hand (LH) side...
View full detailsCoolant Hose is a moulded rubber hose that connects the water pump to the coolant manifold within the engine cooling circuit, carrying coolant from...
View full detailscaliper front LH early Defender 90 upto ca. 1986. - Upto axle number 22L09654 (RHS) - and upto 23L05987 (LHS). - Also from axle number 22L10192 ...
View full detailscaliper front RH early Defender 90 upto ca. 1986. - Upto axle number 22L09654 (RHS) - and upto 23L05987 (LHS). - Also from axle number 22L10192 ...
View full detailsCylinder Head Gasket of composite construction for the 3.5L V8 petrol engine. The gasket seals the joint between the cylinder head and the block, ...
View full detailsStep Assembly - Rear - Defender 90 XA On
Bearing needle roller
Oil Cooler Return Pipe for the engine oil cooling system of the Defender, carrying cooled oil from the oil cooler back to the engine. This pipe is...
View full detailsOuter Wing is the left-hand front wing outer skin panel, moulded in ABS plastic. It forms the visible outer surface of the front wing, covering th...
View full detailsMainshaft Gear operates on the mainshaft of the LT230 transfer gearbox. This 28-tooth, cross-drilled gear transmits drive through the transfer case.
Selector Fork is the 1st/2nd gear selector fork for the 5-speed manual gearbox. It engages the 1st/2nd synchroniser sleeve, moving it along the ma...
View full detailsTop Link Bracket for the rear suspension, right-hand side. This chassis-mounted bracket provides the upper pivot point for the rear suspension lin...
View full detailsFront Floor Contour Mat Kit is a pair of shaped rubber mats for the front cabin footwells, forming part of the interior floor protection. Each mat...
View full detailsKit diff wh OEM NLA AFTER STOCK ENDS
Centrifugal oil filter housing assembly for the Td5 2.5L 5-cylinder turbo diesel, mounted on the oil cooler and filter assembly at the side of the ...
View full detailsTailgate Rear Half Door Kit converts the original fold-down tailgate into a side-hinged half door, matching the style fitted as standard to Station...
View full detailsExhaust Bracket for the exhaust system mounting. The bracket supports and locates a section of the exhaust line against the underbody, typically w...
View full detailsIntercooler Hose for the 200TDi 2.5L turbocharged diesel engine intercooler circuit on the Defender. This hose forms part of the charge air routin...
View full detailsOil Filter Adaptor for the engine lubrication circuit, mounting the oil filter to the cylinder block. The adaptor forms the interface between the ...
View full detailsComplete Cylinder Head for the 300 TDi 2.5L diesel engine, supplied fully assembled and ready to fit. The head is delivered built up with the valv...
View full detailsHalf Chassis - a replacement half-section of the ladder-frame chassis, covering the 200 TDi and 300 TDi diesel applications. Replaces one corroded...
View full detailsFuel Tank - Secondary - 15 Gallon is the auxiliary side-mounted fuel tank for the Defender 110 Hard Top and Pick-Up. This secondary tank supplemen...
View full detailsFront Door Lock Striker Seal fits around the door lock striker on the front door, sealing the aperture where the latch engages the body. This is t...
View full detailsCap Plug for the rocker shaft on 2.25L and 2.5L 4-cylinder petrol and diesel engines. The plug seals the end of the rocker shaft within the cylind...
View full detailsPiston Assembly - +0.020" Oversize for the 300Tdi 2.5L 4-Cylinder Turbo Diesel engine. This piston is machined to a diameter 0.020" (approximately...
View full detailsBrake Caliper Repair Kit - Rear is the piston seal set for overhauling one rear brake caliper in the foundation braking system. The kit renews the...
View full detailsMain bearing kit 0.020" undersize OEM AE
Power steering pipe forming the low-pressure return leg of the power steering hydraulic circuit, running from the steering box return port back to ...
View full detailsBearing transfer box LT230 intermediate shaft
Power Steering Pump - V8
Rear Radius Arm Mount is the chassis bracket that anchors the rear trailing link to the chassis on the right-hand side. The trailing link controls...
View full detailsRear Window Glass for the rear door, part of the rear door glazing. Heated glass with an integral electric demist element and a Sundym solar tint, ...
View full detailsService Filter Kit for the 200 TDi 2.5L turbo diesel engine, grouping the filters and sealing washers required for a routine engine service under a...
View full detailsCrown Wheel and Pinion Set - the final-drive gear pair inside the axle differential. The pinion takes drive from the propeller shaft and meshes wi...
View full detailsDifferential Carrier for the front or rear axle, transmitting drive from the propshaft to the axle halfshafts. The carrier holds the crown wheel a...
View full detailsTurbo Oil Drain Pipe returns lubricating oil from the turbocharger bearing housing to the sump. Fitted to the 2.5L turbo diesel and 200TDi engines.
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →