for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Sliding Window Assembly - rear side, right-hand. The glazed rear side window unit for the right-hand side, comprising the glass panes within their ...
View full detailsHand Throttle Control Cable for the Defender, allowing the driver to set and hold a fixed engine speed independently of the accelerator pedal. The...
View full detailsMainshaft for the LT77 five-speed manual gearbox, Suffix H specification. The mainshaft is the gearbox output shaft. It carries the synchroniser h...
View full detailsRear Quarter Window Glass in clear (untinted) glass for the rear body side. It fits the quarter window aperture in the rear body, located alongsid...
View full detailsO-Ring for the LT77 five-speed manual gearbox. It seals the mainshaft and extension case joint against transmission oil loss.
Differential Shim, 0.074in, used during differential build to set bearing preload and gear alignment. It sits against the differential carrier sid...
View full detailsRadiator Area Retention Clip used in the cooling system assembly. This clip secures cooling system components - including fan cowl panels and radi...
View full detailsFuel Tank Sender Unit for the Defender Pick-Up auxiliary fuel tank. The sender unit mounts inside the fuel tank and uses a float-operated potentio...
View full detailsTiming Cover Gasket for the 2.5L four-cylinder naturally aspirated diesel and turbo diesel engines, sealing the front (timing) cover to the cylinde...
View full detailsRear Exhaust Silencer is the final silencer in the exhaust line, mounted downstream of the intermediate pipe. It attenuates exhaust gas pulsation a...
View full detailsSupport Bracket for the upper rear body section, forming part of the rear body-to-chassis structure. It locates and supports the upper rear body p...
View full detailsSeat Frame - LH for the left-hand front seat assembly in Defender from (V)7A000001. The steel base frame forms the structural foundation of the LH...
View full detailsCastor Correction Kit - 44mm Wide Bush for the front suspension radius arm assembly on the Defender, Discovery 1, and Range Rover Classic. Lifting...
View full detailsGlass Channel - Rear Quarter seats the rear quarter glass within the rear side door frame, forming the bedded run that locates and weatherseals the...
View full detailsRelief Valve Spring is the coil spring that controls the opening pressure of the oil pressure relief valve in the 300Tdi engine lubrication system....
View full detailsFront Housing Gasket - LT77 5-Speed Gearbox This gasket seals the joint between the front housing and the main gearbox casing on the LT77 5-speed ...
View full detailsGlass Channel for the fixed quarter light in the rear side door, retaining the 4mm glass panel within the door frame.
Cover fuse box (For the 2 bolts order 2x MTC9968)
Front Door Latch Link - a connecting link within the front door latch mechanism, transferring movement from the handle and lock to the latch to loc...
View full detailsDifferential Fixing Bolt used on the front and rear axle differential assemblies. It is one of the bolts securing the differential assembly, clamp...
View full detailsHigh-Mounted Stop Lamp Stud is a mounting stud for the high-level stop lamp. It secures the high-level (centre) stop lamp to its mounting point on...
View full detailsCrossmember Assembly - the gearbox mounting crossmember section of the chassis frame. This welded steel crossmember spans the two chassis rails at...
View full detailso-ring sealing shaft reverse gear LT95 4-speed - S3 109" stage one V8 - 110" V8 4-speed manual - RRclassic 4- speed manual - 101" Forward Control
Copper Sealing Washer - a crush washer used to seal banjo and union connections throughout the diesel fuel system, at fuel pipes, filters and sedim...
View full detailsSynchromesh Ring for the five-speed manual gearbox mainshaft. The synchro (baulk) ring matches the speed of the gear to the synchro hub before eng...
View full detailsVacuum Pump Rotor Blade for the engine-driven brake servo vacuum pump. The blade runs within the rotor of the vacuum pump, generating the vacuum t...
View full detailsset screw M6 x 25mm 8.8 various applications
Screw - 10 UNF x 3/8 is a fixing in No.10 UNF (Unified National Fine) thread, 3/8 inch in length, used in fascia and dash assembly applications. Fi...
View full detailsCoolant Hose for the engine cooling circuit, connecting the thermostat housing to the coolant pump pipe. Fitted to the 2.4L Td4 four-cylinder turb...
View full detailsRadiator Bottom Hose connecting the radiator outlet to the engine thermostat housing within the cooling circuit. It returns cooled coolant from th...
View full detailsDoor Glass for the front door, left-hand side, in light green tinted glass. This is the main glass panel for the front door, forming part of the d...
View full detailsTransfer Box Differential Lock Clevis in the centre differential lock linkage. Connects the diff-lock actuating linkage that engages and releases ...
View full detailsThrust Washer - intermediate shaft thrust washer for the LT95 four-speed gearbox. It controls the end-float of the intermediate (lay) shaft, takin...
View full detailsSteel Wheel - a 5.5J x 16 pressed-steel rim finished in Limestone gloss. This is a tube-type rim: it is not sealed for tubeless running and must b...
View full detailsLocking Wheel Nut Key - Code H, the keyed adaptor that engages the splined pattern of Code H locking wheel nuts. The key is placed over the lockin...
View full detailsLocking Wheel Nut Key - Code E, the keyed adaptor that engages the splined pattern of Code E locking wheel nuts. The key is placed over the lockin...
View full detailsFront Door Card is the interior trim panel that covers the inner structure of the front door, concealing the window regulator, latch linkage and wi...
View full detailsSpare Wheel Carrier Clamp Plate secures a bonnet-mounted spare wheel to its carrier. The plate clamps against the wheel to hold it firmly on the c...
View full detailsSpare Wheel Carrier mounts to the rear door to carry the spare wheel externally. It bolts through the door and provides the stud plate onto which ...
View full detailsBattery Clamp J-Bolt is the J-shaped hold-down bolt that secures the battery to its tray. The hooked end locates in the battery tray while the thr...
View full detailsSpare Wheel Carrier Bolt for a bonnet-mounted spare wheel carrier, securing the wheel clamp to the bonnet mounting. Suits both the bar-type and rin...
View full detailsSpare Wheel Cover - a soft cover that fits over an externally mounted spare wheel to shield the tyre and rim from dirt, road grime, moisture and UV...
View full detailsWheel Arch Chequer Plate - front, left-hand. A Safari-style chequered aluminium protection plate fitted over the front wheel arch. The plate cover...
View full detailsWheel Arch Chequer Plate - front, right-hand. A Safari-style chequered aluminium protection plate fitted over the front wheel arch. The plate cove...
View full detailsWoodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...
View full detailsTiming Pin (Short) is a workshop special tool used to set the engine timing on the Td5 2.5-litre five-cylinder turbo diesel. The pin locates throu...
View full detailsGlass Run Channel - window guide channel for the rear side door, fitted within the door frame around the glass aperture. It lines the run in which...
View full detailsBody Corner Capping, right-hand, galvanised steel. The protective capping that covers the rear corner of the body where the side and rear panels me...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →