for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Screw - No. 10 x 1 in. Secures the instrument binnacle cowl and interior air-deflector trim. Sized for self-tapping installation into moulded trim...
View full detailsDoor Striker Shim - a spacer fitted behind the front door latch striker on the body pillar. It packs the striker outward from its mounting face to ...
View full detailsWheelarch Eyebrow is the front wheelarch eyebrow moulding, part of the front wheelarch trim assembly. It mounts to the upper section of the front ...
View full detailsFront Rope Retaining Hook - Left Hand Side for the soft-top hood system on Series and Defender Land Rovers. This hook is part of the hoodstick and...
View full detailsHook for the soft top retaining rope, part of the hood and hoodstick assembly. Secures the rope that runs along the soft top drain channels.
Piston for the 3.5L Rover V8 petrol engine, supplied at +0.020" oversize with an 8.13:1 compression ratio. The +0.020" oversize suits a rebored bl...
View full detailsInternal Floor Chequer Plate is an aluminium protective covering for the internal cabin floor. The chequer-pattern aluminium plate fits over the f...
View full detailsBolt securing the exhaust manifold on the Rover V8 petrol engine. A 3/8" UNC x 1 1/8" fastener used to retain the exhaust manifold to the cylinder...
View full detailsReconditioned Td5 Engine is a rebuilt 2.5L five-cylinder turbo-diesel long block, supplied in the late "15P" specification with Bosch electronic di...
View full detailsStatic Lap Belt - a two-point lap seat belt for a centre or side-facing seating position. The webbing is a fixed length and is adjusted by hand to...
View full detailsDistributor Coupling - drive coupling for the distributor. Transmits drive to the distributor shaft on the 2.25L and 2.5L petrol engines.
LED Daytime Running Lights - Pair for the front lighting system, designed to fit the DA9500 front bumper. Each lamp is fitted with 8 ultra-bright L...
View full detailsWindow Regulator Assembly for the side door glass, right-hand side. Part of the door window lift mechanism. The regulator mounts inside the door s...
View full detailsCylinder Head Bolt - a 7/16" UNC x 2-1/4" short-type bolt for the Rover V8, part of the cylinder head fixings. This is the shorter of the head bol...
View full detailsMudshield Bracket supports the rear brake disc mudshield (splash/backing shield) at the rear axle. The bracket locates the shield behind the brake...
View full detailsAxle Spring Mount forms the lower seat for the rear coil spring, welding onto the rear axle casing to locate and retain the base of the spring. Th...
View full detailsSpare Wheel Cover fits over an externally mounted spare wheel to protect the tyre and wheel from weather, road dirt and UV exposure. This is the h...
View full detailsFront Outer Wing is the Right Hand (RH) outer body panel that covers the front wheel arch and inner wing. It mounts along the front bulkhead and f...
View full detailsFront Wing Protector - Rear Section, part of the exterior body protection panel set for the front wings. The panel covers the rear portion of the ...
View full detailsWindscreen Washer Reservoir
Boost-Style Alloy Wheel, 16" x 7", finished in silver. A cast alloy road wheel of the Boost design pattern, suitable for on- and off-road use. Cen...
View full detailssensor MAP TD5 manifold pressure
Glass Retainer is the vertical glazing retainer for the rear end door assembly. Holds the rear door glass along its vertical edge.
Door Handle Interior LH
Camber Bush Set for the front radius arms, 38mm wide. The bushes locate in the front radius arm mountings and set the caster and camber geometry o...
View full detailsRoller Fairlead - zinc coated - for steel cable winches. This four-roller fairlead mounts to the front of a winch bumper and guides the steel cabl...
View full detailsPortable Jump Starter and Air Compressor - a handheld 12V power pack combining a battery jump starter, power bank, tyre inflator and LED work light...
View full detailsDifferential Reconditioned 10 Splines
Air Conditioning Kit for retrofitting front air conditioning to TDCi Defenders that left the factory without it. Designed as an OE-style installat...
View full detailsExhaust Silencer a silencer in the exhaust system for the 300TDi diesel engine. It attenuates exhaust noise as gas passes through the system on it...
View full detailsHalogen Bulb - H4 100/80W (Non-CE). Dual-filament headlight bulb rated 100W high beam and 80W low beam, providing increased light output over the s...
View full detailsIntercooler Hose Assembly for the turbocharger-to-intercooler charge air circuit on the Td5 2.5L 5-Cylinder Turbo Diesel engine. This rubber hose ...
View full detailsOil Cooler Feed Pipe for the engine oil cooling system of the Defender, carrying pressurised oil from the engine to the oil cooler. This pipe is p...
View full detailsSeat Back Cover - Black Vinyl is a replacement cover for the front seat squab (backrest), finished in black vinyl. It fits over the seat back foam...
View full detailsAluminium Mudflap Mounting Kit - a 2mm chequer plate set that provides the mounting surface for the rear mudflaps. Each plate sits between the mud...
View full detailsRear Wing Protector - an exterior body protection panel fitted over the top surface of the rear wing. It shields the wing bodywork from scuffing, ...
View full detailsSafari-style rear door, designed to accommodate a spare wheel carrier for added functionality. Compatible with: Land Rover Defender 90/110 (Appr...
View full detailsRear Corner Wing Protector - lowline profile, 2 mm plate. The rear body corners are the first thing to meet a gatepost, tree or bank when reversin...
View full detailsFront Hazard Light Wiring Harness is a section of the front lighting wiring loom that carries the supply and switching feeds to the front hazard an...
View full detailsCamshaft Cover Gasket for the 2.2L Puma diesel engine. This gasket seals the camshaft cover to the cylinder head, containing oil within the valve ...
View full detailsEGR Cooler for the exhaust gas recirculation circuit of the 2.4L TDCi Puma diesel engine. The cooler lowers the temperature of recirculated exhaus...
View full detailsOil Filter Bowl for the Puma 2.4L and 2.2L TDCi diesel engine. The housing that retains the oil filter element within the engine lubrication circui...
View full detailsExhaust Camshaft for the 2.4L Duratorq TDCi (Puma) turbo diesel engine. Mounted in the cylinder head as part of the overhead-cam valvetrain, this ...
View full detailsLoadspace Liner lines the rear loadspace to protect the load floor against scratching, scuffing and spills. Shaped to fit the loadspace, it shield...
View full detailsDoor Lock Link for the left-hand door lock mechanism. This threaded operating rod transfers movement between the door latch and the lock actuation...
View full detailsDoor Lock Link for the right-hand door lock mechanism. This threaded operating rod transfers movement between the door latch and the lock actuatio...
View full detailsPolyurethane Suspension Bush Set - Black - a complete set of black polyurethane bushes to replace the full complement of suspension mounting bushes...
View full detailsDefender 2007 on front door only barrel
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →