for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Piston Assembly for the 2.5 four-cylinder naturally aspirated diesel, standard size. The piston transfers combustion pressure to the connecting ro...
View full detailsPiston - 2.5L N/A Diesel - 0.020" Oversize for the Defender fitted with the 2.5L naturally-aspirated diesel engine, for use during engine overhaul ...
View full detailsRear Door - the rear load (tail) door that closes the back of the body. Supplied unglazed, the door is pre-drilled with mounting holes to accept a...
View full detailsPiston Ring Kit
Carburettor Overhaul Kit - service kit for the Weber twin-choke carburettor fitted to the 2.25L and 2.5L four-cylinder petrol engines. The kit is ...
View full detailsRegulator & Brush Assembly - the combined voltage regulator and brush box fitted to Lucas alternators in the charging circuit. The unit mounts...
View full detailsIgnition Solenoid - 2.5L Petrol
Front Bumperette - a compact protection unit fitted at the front of the vehicle. It provides localised impact protection to the front end. Manufac...
View full detailsPiston Ring Set for the 2.25L 4-cylinder petrol engine, ground to +0.040" (1.0mm) oversize for use with rebored cylinder bores. The rings seal the...
View full detailsPower Steering Reservoir Cover Seal for the power steering hydraulic circuit. The seal fits between the reservoir cover and the fluid reservoir bo...
View full detailsWheel Cylinder Repair Kit - Rear - a seal kit for reconditioning the rear wheel brake cylinder, part of the rear drum brake hydraulic circuit. The ...
View full detailsCrown Wheel & Pinion is the final-drive gear set within the differential, transferring drive from the propshaft into the axle and turning it th...
View full detailsConrod Bearing Set - V8 (0.020" Undersize) is a complete set of big-end bearing shells for the connecting rods of the Rover V8 petrol engine. The ...
View full detailsMain Bearing Set +0.030" 2,25
Towing Pin provides a centre towing and recovery attachment point on the front bumper. The pin mounts at the centre of the bumper to give a fixed ...
View full detailsBumperette - Rear - LH - Black is the left-hand rear bumperette, a corner protection unit mounted at the rear of the chassis. It bolts to the rear...
View full detailsBumperette - Rear - RH for the rear bumper assembly. This right-hand rear bumperette bolts to the outer end of the rear bumper cross-member, provi...
View full detailsBush Assembly Anti Roll Bar
External Roll Cage - a full external bolt-in roll cage that fits around the outside of the body to provide rollover protection. It is a 6-point bo...
View full detailsIn-Tank Fuel Pump - Petrol - Non-EFI for carburettor petrol fuel systems. Sited inside the fuel tank, this pump draws fuel from the tank and deliv...
View full detailsSpeedometer Cable - V8 - RH The speedometer drive cable, part of the instrument drive assembly on right-hand drive V8 petrol applications. It tran...
View full detailsTurbocharger Oil Drain Pipe - return line carrying lubricating oil from the turbocharger bearing housing back to the sump on the 2.5L Td5 five-cyli...
View full detailsOil Cooler Repair Kit for the Td5 engine, serving the oil cooler within the engine lubrication and cooling circuit. The kit renews the oil cooler ...
View full detailsPower Steering Pump for the steering hydraulic circuit of the 2.5L 200TDi four-cylinder turbo-diesel engine. Belt-driven from the engine, it draws ...
View full detailsIntermediate Exhaust Pipe for the 2.5TD turbo diesel engine, forming the centre section of the exhaust system on Defender 90 and 110 models. This ...
View full detailsExhaust Tailpipe Silencer is the rear silencer (back box) of the exhaust system, fitted at the tailpipe end of the line. It sits downstream of the...
View full detailsRear Exhaust Silencer sits at the back of the exhaust system, providing the final stage of noise reduction before gases leave at the tailpipe. Int...
View full detailsRear Silencer & Tailpipe - Stainless - the rear section of the exhaust system, combining the rear silencer and tailpipe in a single assembly, c...
View full detailsCentre Exhaust Silencer sits in the middle section of the exhaust system, reducing noise as gases pass from the front pipe rearward toward the tail...
View full detailsExhaust Downpipe for the 2.25L 4-cylinder petrol engine. The downpipe is the first section of the exhaust system. It bolts to the exhaust manifold...
View full detailsPDWA Valve (Pressure Differential Warning Actuator) for the brake hydraulic circuit. This valve connects the front and rear brake circuits and mon...
View full detailsHeater Hose for the cabin heating circuit, carrying engine coolant between the cooling system and the heater matrix to supply heat to the cabin. S...
View full detailsHeater Hose running to the heater, part of the heater pipes and hoses assembly. The hose carries engine coolant to the heater matrix, where cabin ...
View full detailsLower Radiator Hose in the engine cooling circuit, carrying coolant from the radiator bottom outlet to the water pump inlet. Moulded rubber hose f...
View full detailsDrain Channel - Rear Side Door installed vertically within the rear side door frame, channelling water away from the fixed quarter light aperture a...
View full detailsChannel fitted to the top of the Defender rear side door frame, guiding and retaining the upper edge of the main drop glass as it operates.
Rear Quarter Glass is a fixed side glazing panel that sits in the rear body quarter, forming the glazed opening behind the rear side door. It loca...
View full detailsStiffener
Finger Pull - Inner - Right-Hand for the door top sliding glass assembly. This inner finger pull is the grip mounted to the inner face of the slid...
View full detailsSending is only possible by pallet. Too fragile for normal parcel delivery.
Soft Top Hood Retainer Spindle for the soft top retaining hardware. The spindle forms part of the hood retainer mechanism, providing the pivot or ...
View full detailsBody Mounting Bracket, left hand, front position, from the rear body mounting arrangement. The bracket forms the interface between the rear body t...
View full detailsBody Mounting Bracket, right hand, front position, from the rear body mounting arrangement. The bracket forms the interface between the rear body ...
View full detailsDoor Lock Striker - LH is the striker that the left-hand door latch engages to hold the door closed. Mounted on the body pillar, it provides the f...
View full detailsDoor Striker – RH is the right-hand striker plate for the rear-end door latch. The door latch engages this striker to draw the door closed and hol...
View full detailsStud Plate for the front sill channel section. Fitted within the front sill channel, this bolt plate provides captive attachment points for sill o...
View full detailsDoor Checker Bracket Assembly - Rear - LH is the door check mechanism for the left-hand rear door. It links the door to the body pillar and limits...
View full details1/3 chassis 90 TOT TD5 EXTRA verzendkosten gebruik code AVK40.
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →