Land Rover Discovery 1 Parts

Track Rod End with right-hand thread, fitting at the outer end of the track rod within the steering linkage on the Defender, Discovery 1, and Range...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Front Propshaft This propshaft transmits drive from the transfer box output to the front axle differential, forming part of the four-wheel-drive d...

Stub Axle Bolt is a hex-head retaining screw that secures the front stub axle to the swivel pin housing. The stub axle carries the wheel hub and b...

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...

Water Pump for the 200TDi 2.5L turbo diesel engine, operating in the engine cooling circuit. Belt-driven from the crankshaft, the pump circulates ...

Track Rod End with a right-hand thread, forming part of the steering linkage. The track rod end is the articulating ball joint that connects the t...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

Oil seal

Fuel Filler Cap that seals the fuel tank filler neck. Non-locking type with a black finish, closing the filler neck against fuel vapour loss and t...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Flanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...

Differential Carrier Bearing is a taper roller bearing that supports the differential carrier within the axle, as part of the crownwheel and pinion...

Flange Bolt - M8 x 85mm hex bolt with an integrated flange beneath the head. The flange spreads the clamping load across a wider bearing surface a...

Hose pump to box

Bolt 10.9 M12 x 100

Single Pipe Clip, a routing clip that retains a single pipe or line against the chassis or body. It holds fuel, evaporative-loss or brake pipework...

Brake Pipe Clip (double) used to route and secure rigid brake pipes within the braking hydraulic system. The double form retains two brake pipes s...

Wheel spacer kit fitted between the wheel hub and road wheel within the wheel mounting assembly. The spacers move the wheel mounting face outward...

Cable Clip secures wiring harnesses, breather pipes and similar runs to the body, chassis or panel. It locates in an 8mm mounting hole and holds t...

Air Filter element for the air cleaner housing on the induction system. The element traps dust and airborne particles from the incoming air before...

Repair kit adjuster hand brake

Level plug R380

Cylinder Head Bolt, M10 x 117 mm for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It secures the cylinder head to the eng...

Viscous Fan Coupling - temperature-sensitive drive coupling between the water pump drive and the engine cooling fan. It modulates fan speed with u...

Rear Crankshaft Packing Strip (T-Piece) forms part of the rear crankshaft oil seal arrangement at the back of the cylinder block. The T-piece pack...

Tow Ball Step is a rear access step that locates over the tow ball, providing two tread levels to make reaching the rear door, load area or roof ea...

Bolt - Bracket to Chassis is an M10 x 60 mm fastener that secures a bracket to the vehicle chassis frame. It has a 10 mm nominal thread diameter a...

Alternator 300TDi (with pulley)

Head Gasket - 3.5L V8 - Metal is the cylinder head gasket for the 3.5L V8 petrol engine, sealing the joint between a cylinder head and the engine b...

Track Rod & Steering Damper Bush for the steering linkage, locating the steering damper at its mounting eye. The bush insulates the damper mou...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Injection Pump Gasket seals the fuel injection pump to its mounting face on the timing case of the 200Tdi and 300Tdi 2.5L turbo diesel engines. Th...

Timing Cover Mudshield is the pressed shield that fits over the timing cover at the front of the engine. It screens the timing case and front pull...

O-Ring for the power steering hydraulic circuit, sealing a union on the 6mm power steering pipe. The O-ring seats at the connection between the po...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. This plastic plug cl...

A/C Drive Belt drives the air-conditioning compressor on the 2.5L 300TDi diesel. Run from the crankshaft pulley, it transmits drive to the air-con...

Wheel Centre Cap in a Silver Sparkle finish with the embossed Land Rover logo, fitting the centre bore of the alloy road wheel. It conceals the hub...

Rubber Plug Cushion is a moulded rubber blanking plug that fits into a pre-formed aperture in the body, frame or seat base to close off the opening...

Brake Disc - Solid - Rear is the rear brake disc, mounting to the rear hub and providing the friction surface the brake pads clamp against during b...

Inlet Manifold Gasket for the Rover V8 petrol engine, sealing the inlet manifold where it seats in the valley between the two cylinder banks. This...

O-Ring for the speedometer drive spindle on the LT230 transfer gearbox. Seals the spindle housing where the speedometer drive take-off enters the ...

Oil Filler Cap O-Ring seals the oil filler cap to the rocker cover. It forms an oil-tight seal at the cap-to-cover joint, preventing oil leakage a...

Exhaust Mount Washer from the exhaust mounting hardware. It seats beneath the fastener at an exhaust mounting point, spreading the clamp load acros...

Washer from the anti-roll bar mounting hardware. It seats beneath the fastener that secures the anti-roll bar (stabiliser bar) to its chassis mount...

Rear Output Shaft Flange for the LT230 two-speed transfer case. The LT230 distributes drive to the front and rear propshafts. This flange mounts o...

Engine Overhaul Gasket & Seal Set for the 200TDi diesel engine, covering the bottom end of the engine. This set provides the gaskets and seals...

Handbrake Spring Kit for the transmission brake – the drum-type parking brake mounted at the transfer box output. The kit comprises the shoe reten...