Land Rover Discovery 1 Parts

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Washer - a plain flat washer used as a general-purpose fastening component across many assemblies on the vehicle. Fitted under a bolt head or nut,...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

Fuse - 10A for Land Rover electrical systems. This 10A fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Front Cover Gasket sealing the timing cover to the front face of the cylinder block on the 300TDi 2.5L turbo diesel engine. It forms the oil-tight...

Polyurethane Suspension Bush Kit A complete polyurethane bush set that replaces the original rubber suspension bushes across the chassis-mounted su...

Shock Absorber Bush Kit for the mounting points of Terrafirma TS-series shock absorbers. The kit provides the hardware required to replace worn bu...

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Fuse rated at 15A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 15 amps, the fuse breaks the connection w...

Screw hex HD 3/8" UNC x 1-1/4"

Sump Plug for the engine oil sump drain. Fitted to the sump drain port and removed at each oil change to drain the engine oil. The sealing washer ...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

These locking wheel nuts are suitable for all alloy wheels that use original Land Rover alloy wheel nuts. Set of 5 locking wheel nuts and 1 key.

Baulk Ring for the R380 5-speed manual gearbox synchromesh assembly. The baulk ring (also known as the synchromesh ring) is the friction cone elem...

heavy duty spring front RR/disco pair, like DA4201 and TF014.

Nut An M4 hexagonal plain nut. A general-purpose metric fastener used across a wide range of assemblies. Takes a 7 mm spanner.

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Ball Steel Bearing

Crankshaft Bolt is the retaining bolt that secures the pulley and damper assembly to the nose of the crankshaft on the V8 petrol engine. Threaded ...

Power Steering Pipe O-Ring - a seal in the power steering hydraulic circuit. It fits at the union between a power steering pipe and its mating conn...

Vacuum unit V-8

Retaining Plate - gearchange grommet retaining plate for the transfer box. Secures the transfer box gearchange grommet where the gear lever passes...

Radius Arm Bush Set - Polyurethane fits at the axle end of the front radius arms, within the front suspension radius arm and axle location assembly...

Upper Link Bush Set - Polyurethane for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. Supplied as a set of two ...

Crankshaft Pulley for the 300 TDi 2.5L 4-cylinder turbo diesel, mounted on the nose of the crankshaft at the front of the engine. The pulley trans...

Grab Handle in black, an interior assist handle that mounts to the roof trim rail. It provides occupants with a secure handhold when entering or e...

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Clevis pin

Half Shaft Shim is a 1.05mm selective shim used in the front axle drive shaft and hub assembly. It sets the endfloat of the front half shaft drive...

Clutch Push Rod (9.2 cm) for the clutch release hydraulic circuit, working between the clutch slave cylinder and the release lever. The rod transm...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Camshaft for the five-bearing four-cylinder engine, running in the cylinder block as the core of the overhead-valve valvetrain. Driven from the cr...

Camshaft O-Ring for the 2.5L four-cylinder diesel engines, including the naturally aspirated diesel, turbo diesel and 200TDi. This O-ring forms th...

Throttle Potentiometer Gasket seals the throttle position sensor (throttle potentiometer) to the throttle body on the V8 EFI system. It forms the ...

Inlet Valve Rocker Arm - a valvetrain component in the rocker shaft assembly of the 2.5L 300 TDi turbo-diesel engine. Mounted on the rocker shaft,...

Exhaust Valve Rocker Arm - a valvetrain component in the rocker shaft assembly of the 2.5L 300 TDi turbo-diesel engine. Mounted on the rocker shaf...

Timing Belt Tensioner for the 200TDi 2.5L turbo diesel engine, part of the camshaft timing belt drive. The tensioner maintains correct tension on ...

Oil Separator Drain Hose for the crankcase ventilation system on the 2.5L naturally aspirated diesel and 200TDi turbo diesel engines. It drains th...

Fuel Tank Sender Wrench is a special service tool for the fuel tank sender unit assembly. It engages the metal locking ring that retains the fuel ...

Bolt with a 3/8" UNF (Unified National Fine) imperial thread and a 1-1/2" shank length. A hex-head fastener for general assembly and fixing applic...

ABS Pump Relay for the Anti-lock Braking System electrical circuit. A normally open, black-bodied relay that controls power supply to the ABS pump...

Camshaft Bearing Set comprises the plain bearing shells that support the camshaft within the cylinder block of the four-cylinder engine. The beari...

Union Nut for the fuel pipe in the fuel delivery system. This M12 union nut clamps a fuel pipe to its mating union or component port, drawing the ...

Clutch Cover is the pressure plate assembly of the manual transmission clutch, for V8 petrol applications. It bolts to the engine flywheel and cla...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Swivel Pin Retaining Bolt A fixing bolt for the front axle swivel pin housing. It secures a swivel pin to the swivel pin housing, retaining the pi...

Spring Retaining Plate for the front coil spring suspension. The plate seats the upper end of the front coil spring against the chassis spring seat...