Land Rover Discovery 1 Parts

Sealing Washer - a sealing washer used at cylinder head and thermostat housing joints within the cooling and lubrication circuit. Fitted beneath a...

Electronic Fan Conversion Kit for the cooling system. It replaces the engine-driven viscous fan with a thermostatically controlled electric suction...

Engine Plug is a core (welch) plug that seals the casting holes in the engine. Fitted to the cylinder block, cylinder head water jacket and inlet ...

Needle Bearing - LT77 supports a mainshaft gear on the LT77 5-speed manual gearbox mainshaft, allowing the gear to rotate freely on the shaft. It ...

O-Ring for the oil strainer in the ZF 4-speed automatic transmission. This seal fits the oil strainer (the automatic transmission fluid pickup fil...

Pan Head Screw, M6 x 12mm. Metric pan head screw for use across a range of Land Rover body, chassis, and electrical assemblies.

O-Ring seals the intermediate shaft in the LT230 transfer box, sitting between the shaft mounting and the transfer casing to hold the oil seal at t...

Anti-Roll Bar Bush for the front suspension system, sold as a pair. This bush locates the anti-roll bar at its chassis mounting points, allowing t...

Crown Wheel & Pinion Set - the final-drive gear pair housed within the axle differential. The pinion takes drive from the propshaft and turns t...

Nyloc Nut M5 - M5 hex nyloc (nylon insert) locknut. The nylon insert creates friction against the thread to resist loosening under vibration. Stan...

Locking Wheel Nut Key - Code C for removing locking wheel nuts with the Code C drive profile. The key engages the unique recessed socket of the Co...

Oil Pump Rotor Set - Inner & Outer for the 300TDi engine, fitted to the Defender, Discovery 1, and Range Rover Classic. The oil pump rotor set...

Needle Bearing - LT77 5-Speed Gearbox - Mainshaft This needle roller bearing supports the mainshaft gear cluster within the LT77 5-speed manual ge...

Centre Plate Gasket for the LT77 5-speed manual gearbox. This gasket seals the joint between the main casing sections of the LT77 gearbox, prevent...

Bump Stop Mounting - a weld-on chassis bracket that provides the mounting point for a rear axle bump stop. The bracket is welded to the chassis to...

Oil Pump for the R380 manual gearbox. Mounted at the rear of the gearbox and driven from the output shaft, the pump circulates gearbox oil to lubr...

Hex Nut - 7/16 UNF fixing nut. Used on the fuel pipe unions of the 3.5L V8 twin-carburettor petrol engine. Also supplied as part of a service kit.

Drain Plug Washer is the copper sealing washer for the drain plug on the LT77 manual gearbox. It seats between the magnetic drain plug and the gea...

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Thrust Washer is a 1.15mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Dowel is a precision locating pin that aligns mating components during assembly, setting their position accurately and relieving the securing bolts...

Locking Nut for the steering linkage, retaining a track rod end onto the drag link or track rod. Once the joint is set to position, the nut is tigh...

Seat Belt Fixing Kit provides the mounting hardware used to secure a seat belt assembly to the vehicle body anchorage points. The kit supplies the...

Synchromesh Ring for the R380 5-speed manual gearbox, the intermediate ring for 1st to 4th gears. The synchroniser ring matches the speed of the s...

Wheel Cylinder Brake - RH

Rocker Cover Screw - Long for the Rover 3.5L V8 engine. This long 1/4" UNC x 1-5/16" screw secures the rocker cover to the cylinder head on the Ro...

Inlet Valve for the cylinder head valvetrain of the Rover V8 petrol engine (3.5L, 3.9L, 4.0L and 4.6L variants). It seats in the cylinder head inl...

Flanged Clip Nut is an M6 captive nut retained in a spring-steel clip. The clip pushes onto a panel edge or into a mounting hole to hold the nut c...

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...

Differential Pinion Bearing Shim - 0.064 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Wheel Nuts - set of five, sufficient to secure one wheel. The nuts are sized for the MaxXtrac Mach 5 alloy wheel, giving the correct seat and thre...

Gearbox Selector Pad for the LT77 five-speed manual gearbox. Fits the 5th gear selector within the selector and yoke assembly, forming the bearing...

Automatic Transmission Shaft is a coupling shaft within the ZF 4-speed automatic gearbox assembly. This shaft transmits drive between internal gea...

O-Ring - Diff Lock Selector Shaft - LT230 Transfer Case This O-ring seals the differential lock selector shaft where it passes into the LT230 tran...

Flanged Nut - M6 flanged hex nut for use across a wide range of Land Rover assemblies including engine, drivetrain, body, braking, and electrical a...

Gearbox Oil Seal for the extension case of the LT77 five-speed manual gearbox, sealing the mainshaft output collar. The seal runs on the collar at...

A/C Belt Tensioner Cover for the air conditioning belt drive on 300TDi engines. This cover fits over the tensioner pulley assembly in the A/C auxi...

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...

Plain Washer - 7/16" used in the power steering box assembly. This flat washer is used within the steering hydraulic assembly at the power steerin...

Injector Clip for V8 EFI fuel injection systems, used in the fuel delivery assembly at the intake manifold. This retaining clip secures the fuel i...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Fusible Link is a sacrificial circuit-protection device used in the vehicle electrical system. Rated at 60A and identified by its yellow body, it ...

Kit gasket carb for Rover V8 engines fitted with SU carburetors

Fusible Link - 30A Pink for the electrical protection circuit. A fusible link that installs inline within the wiring harness at a current-protecte...

Paint-clearing screw from the standard fastener range. The thread is formed so that it cuts through the paint film as the screw is driven, leaving...

Synchromesh Ring - inner synchroniser ring for the R380 five-speed manual gearbox. Works within the mainshaft synchroniser assembly to bring the g...

Swivel Recovery Eye Rotating recovery point that bolts through the recovery-point holes in a winch bumper, providing a secure anchor for a shackle ...

Self Tapping Screw for use in Land Rover body, chassis, and hardware applications.