Land Rover Discovery 1 Parts

Brake Pad Set for the rear axle disc brakes, fitting the rear brake calipers. The friction pads clamp against the rear brake discs under caliper a...

Connecting Rod Bearing Set - a set of big-end bearing shells for the Rover V8 petrol engine. The connecting rod bearings are the split shell beari...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Coolant Temperature Sensor threads into the cylinder head and reports engine coolant temperature to the engine management system and the instrument...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

16 x 7 Maxtrac Blindo Alloy Black 5 x 165PCD Offset Et15

O-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...

Coolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...

Flanged Nut - M10 flanged fastener. The integral flange spreads the clamping load over a wider area and resists loosening under vibration, removin...

Raised Air Intake Mantec - 90/110 200TDi

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Drive Belt Air conditioning compressor drive belt for the 200TDi turbo diesel engine, poly-vee (multi-rib) construction. Drives the A/C compressor...

Cylinder Head for the 300 TDi 2.5L four-cylinder turbo diesel engine, supplied as a bare casting without valves. The head bolts to the top face of...

Front Half Shaft for the right-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant vel...

Front Axle CV Joint, heavy-duty, 24-spline, for the front drive shaft. The constant velocity joint sits at the outer end of the front axle shaft an...

Hose - Oil

Taper Roller Bearing for the front output shaft of the LT230 transfer box. Installed within the LT230 transfer case differential lock and output s...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Camshaft Oil Seal - radial oil seal for the 2.5L 300 TDi turbo diesel engine, fitted in the front timing cover within the timing gear assembly. Th...

Connecting Rod Bearing Set for the 2.5L 4-cylinder engine, supplied in 0.030" oversize. These are the big-end shell bearings that fit between the ...

Oil Filler Cap closing the engine oil filler neck on the rocker cover. It seals the filler aperture to keep the lubrication system closed and prev...

Gasket Set

Coupling - Viscous Borgwarner

Swivel Joint Washer located within the Swivel Pin Housing Assembly, sealing the interface between the swivel housing flange and the axle beam face....

Exhaust Manifold Gasket for the 200 TDi diesel engine, sealing the joint between the exhaust manifold and the cylinder head. It seals each exhaust...

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Layshaft Bearing - taper roller bearing supporting the layshaft in the R380 5-speed manual gearbox. The bearing carries the countershaft (layshaft...

Camshaft Seal - Rear

Piston Assembly - +0.020" Oversize for the 300Tdi 2.5L 4-Cylinder Turbo Diesel engine. This piston is machined to a diameter 0.020" (approximately...

Fuel Injector for the 2.5L 300TDi 4-cylinder turbo diesel engine. This direct injection fuel injector delivers metered, atomised fuel into the pre...

Oil Seal for the R380 manual gearbox extension case (rear/tail housing). It seals the output shaft where it exits the extension housing, retaining...

Connecting Rod Bearing Set for the 2.5-litre 4-cylinder engine, including the 200 TDi and 300 TDi diesels. These are the replaceable big-end shell ...

Engine Mounting Bracket - 3.5L V8

Fitting Kit for Pacet Fan

Anti-Roll Bar Bush in the suspension anti-roll bar mounting, locating the stabiliser bar against the chassis. This polyurethane bush cradles the a...

ABS Wheel Speed Sensor - front sensor for the four-wheel anti-lock braking system. The sensor mounts in the front axle housing with its pole piece...

Main Bearing Set 020 (Lc)

Rear Differential Drive Flange Kit for the Land Rover (Rover-type) rear axle. The drive flange mounts to the differential pinion and provides the ...

Engine Overhaul Gasket & Seal Set for the 200TDi diesel engine, covering the bottom end of the engine. This set provides the gaskets and seals...

Conrod Bearing Kit - 0.010" Undersize for Land Rover four-cylinder petrol and diesel engines. Supplies a complete set of connecting rod big-end bea...

Lower Steering Column Universal Joint for the steering column assembly. This universal joint sits at the lower end of the steering shaft, transmitt...

Swivel Pin Housing Thrust Washer for the front axle swivel pin assembly. Installed within the swivel pin housing between the pin head and the hous...