Land Rover Discovery 1 Parts

Cylinder Head for the 300 TDi 2.5L four-cylinder turbo diesel engine, supplied as a bare casting without valves. The head bolts to the top face of...

Rear Flange is the rear output drive flange of the LT230 transfer box. It mounts on the transfer box rear output shaft and forms the bolted coupli...

Half Shaft for the rear axle drive, left-hand side, 24-spline. The half shaft transmits drive from the rear differential to the rear hub. Its inne...

Half Shaft for the rear axle drive, right-hand side, 24-spline. The half shaft transmits drive from the rear differential to the rear hub. Its inn...

Gearchange Lever Oil Seal seals the gearchange lever where it enters the manual gearbox housing. It retains transmission oil around the selector l...

Shim - 1.20 mm front axle hub shim. Fitted in the front axle hub assembly to set the correct spacing and control end-float within the half-shaft a...

Camshaft - the valvetrain camshaft for the overhead-valve V8. Driven from the crankshaft, its lobes act through the tappets, pushrods and rocker ar...

Camshaft - the valvetrain camshaft for the overhead-valve V8. Driven from the crankshaft, its lobes act through the tappets, pushrods and rocker ar...

Camshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...

Linkage

Fuel Filter

Air Flow Sensor for the V8 EFI petrol engine management system, mounted in the intake tract between the air filter and the throttle. Measures the ...

Turbocharger for the forced-induction system of the 2.5L 300 TDi diesel engine, supplied complete with the mid manifold section. Driven by exhaust...

Filler Plug is a red anodised aluminium replacement filler plug for the radiator and thermostat housing filler points. Machined from anodised alum...

Valve Spring for the cylinder head valvetrain. Fitted over the valve stem, it holds the valve closed against its seat and keeps the follower in con...

Injector Clamp secures a fuel injector into the cylinder head on the 2.5L 300TDi turbo diesel engine. It clamps the injector body down against its...

Power Steering Pump Pulley mounts on the power steering pump within the engine's auxiliary drive on the 2.5L 300TDi turbo diesel. Driven by the au...

Camshaft operates the valvetrain of the 2.5L 300TDi diesel engine. Its lobes actuate the pushrods to open and close the inlet and exhaust valves.

Viscous Fan Coupling drives the engine cooling fan on the 3.9L and 4.0L V8 EFI petrol engine. The temperature-sensitive coupling varies fan speed ...

Fuel Injector for the 2.5L 300TDi 4-cylinder turbo diesel engine. This direct injection fuel injector delivers metered, atomised fuel into the pre...

Timing Belt Tensioner for the 200TDi 2.5L turbo diesel engine, part of the camshaft timing belt drive. The tensioner maintains correct tension on ...

Engine Piston for the 2.5L 300 TDi diesel engine, supplied in standard bore size. The piston runs in the cylinder bore and transfers combustion pr...

Front Crankshaft Oil Seal seals the front of the crankshaft where it passes through the timing cover. It prevents oil loss at the crankshaft pulle...

Flywheel Housing Gasket for the 200 TDi diesel engine, sealing the joint between the flywheel (or drive plate) housing and the rear face of the cra...

Rocker Arm Bush is the bearing bush pressed into the rocker arm, carrying it on the rocker shaft. Fitted to 200TDi and 300TDi diesel valvetrains.

Rocker Arm operates on the rocker shaft in the 200TDi diesel valvetrain. Driven by the pushrod, it transfers camshaft motion to actuate the valve.

Rear Spring Spacer Kit for the coil-spring rear suspension, supplied as a pair of blocks that fit between the axle and the spring seats to raise ri...

Limited-Slip Differential is a helical-gear (Detroit TrueTrac type) limited-slip differential centre for the rear axle, with a 10-spline output. T...

Ensure a secure and reliable installation of your heavy-duty rear bumper with this fitting kit, specifically designed for bumper part DA5647. This ...

Rear Radius Arm locates the axle and controls its fore-and-aft movement, with geometry set for a 2 inch suspension lift. The revised arm restores ...

Carburettor Conversion Kit - replaces the twin Stromberg or SU carburettor setup on the Rover V8 with a single four-barrel carburettor mounted on a...

Towing Hitch Pin is the 25mm locking pin for the Dixon Bate 3.5 tonne ball, jaw and pin hitch (DA2123 / RTC8159), retaining the coupling jaw closed...

Differential Pan Cover - weld-in replacement cover for the axle differential housing, incorporating a filler/level plug. The cover welds onto the ...

O-Ring for the R380 five-speed manual gearbox extension case. Seals the oil pump within the gearbox extension housing.

Front Twin Shock Tower (Pair) - an uprated front shock absorber mounting set for coil-sprung suspension that allows a second shock absorber to be f...

Steering Guard - a heavy-gauge steel skid plate that bolts beneath the front of the chassis to shield the steering linkage and steering damper from...

Wheel Nut Cover Removal Tool for Land Rover alloy wheel locking nut covers. This dedicated tool is designed to grip and extract the protective pla...

Upper Link Ball Joint for the rear suspension A-frame (top link). The joint sits at the apex of the rear A-frame, where the frame meets the top of...

Differential Cross Shaft for the Land Rover-type differential. The cross shaft locates through the differential case and carries the two differenti...

Special Bolt

Differential Shim, 0.038in, used during differential build to set bearing preload and gear mesh. It sits against the differential carrier side bea...

Crankshaft Thrust Washer - 0.010in oversize, supplied as a pair. Fitted at the centre main bearing of the four-cylinder engine to control cranksha...

Baulk Ring (Synchroniser Ring) for the LT77 five-speed manual gearbox. Fits the mainshaft synchromesh hubs to match shaft speeds during gear engag...

Oil Pump O-Ring seals the oil pump to the cylinder block in the engine lubrication system. It seals the joint between the pump and its mounting fa...