Land Rover Discovery 1 Parts

Speedo cable oil seal retainer plate

Clutch Release Bush for V8 petrol applications, located within the clutch assembly at the rear of the crankshaft. The bush seats in the spigot rec...

Core Plug (cup/expansion plug) seals a casting core hole in the cylinder block, fitted at the rear of the block. It closes the openings left by th...

Thermostat Housing Gasket for the 200TDi 2.5L turbo-diesel engine, sealing the thermostat housing to the cylinder head within the engine cooling ci...

Selector yoke spherical bush

Heater Outlet Hose is the coolant return hose from the heater matrix in the cabin heating circuit. It carries coolant from the outlet side of the ...

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Flame Trap fits into the crankcase ventilation circuit of the V8 twin-carburettor petrol engine, between the crankcase breather and the carburettor...

Grommet

Expansion Tank Hose connects the coolant expansion (header) tank into the cooling circuit. It carries coolant between the expansion tank and the r...

Brake Disc - Solid - Front is the front brake disc, mounting to the wheel hub and providing the friction surface the brake pads clamp against durin...

Brake Caliper Repair Kit - 4-Piston

Screw – a No. 6 × 1/2 in self-tapping screw used to secure interior trim and panel fixings, such as the instrument binnacle, fascia mouldings and a...

Brake pipe clip

Rear Brake Caliper for the left-hand side of the rear axle, part of the hydraulic braking circuit. The caliper carries the hydraulic pistons that ...

Headlamp Fixing Kit - replacement mounting and adjustment hardware for the front headlamp. The kit renews the fixing clips and adjusters that reta...

Ball Bearing for the transfer box, supporting the output shaft and its output flange. Fitted in the LT230 and NV225 transfer boxes, the bearing lo...

Hex-head bolt, 5/16" UNC thread, 1" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and socke...

Set Screw, a hexagon-head metric fastener, M10 x 25mm. In Land Rover terminology a set screw is a bolt threaded along its full length rather than ...

Screw M6 x 20 pan-head screw. It can be used in place of LR083229 (RYG500650 / DYP500210 / EYG50080) but is not identical: this screw has no capti...

Voor alle LT77 versnellingsbakken

Drive Belt for the auxiliary (accessory) drive system of the 300 TDi turbo diesel engine. The belt transmits drive from the crankshaft pulley to th...

Front Drive Shaft, left-hand, part of the front axle drive assembly. The shaft transmits torque from the front differential to the front wheel hub...

Steering Drop Arm Puller - a specialist tool for drawing the drop arm off the splined output shaft of the steering box. The drop arm is a tight ta...

Oil Cooler Thermostat - the thermostatic control valve in the engine oil cooling circuit. It regulates oil flow to the oil cooler in response to o...

Alarm Remote Transmitter, the handset used for remote operation of the vehicle's anti-theft alarm and central locking system. The unit transmits a...

Hydraulic Fluid - Rock Oil Power Steering and Active Cornering Fluid, 1 litre. Formulated for power steering systems and Active Cornering Enhanceme...

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This version c...

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

A-frame Ball Joint Fitting Kit – the mounting hardware for the rear A-frame ball joint and its housing. The fixings secure the ball-joint housing t...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Head gasket set 3.9 EFI MA on

Side Repeater Lens is the lens cover for the side repeater indicator lamp. It fits over the repeater lamp bulb to seal the unit and colour the emi...

Anti-roll bar bush

Clutch Hose forms part of the clutch hydraulic circuit, carrying fluid between the clutch master cylinder and the slave cylinder. The flexible hos...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Kit latch bonnet catch LHD

Turret Fitting Kit - Galvanised - Front - Pair

Starter Motor for the 2.5L 4-cylinder diesel engine, part of the engine electrical starting circuit. When the ignition is operated the solenoid th...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

CuNiFer Clutch Pipe, 1/4" outer diameter, supplied for the clutch hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough t...

Stud M8 x 25

Fuel Lift Pump for the low-pressure fuel supply circuit of the 2.5L 300TDi turbo diesel engine. This engine-mounted mechanical diaphragm pump draw...

Brake Vacuum Pump for the 300 TDi 2.5L turbo-diesel engine, mounted on the engine as part of the brake vacuum circuit. Driven mechanically by the ...

Cam Cover Sealing Washer Seals a camshaft cover retaining bolt on the 300 TDi 2.5L turbo diesel engine. Fitted beneath the head of the cam (rocker...

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

Rubber Mounting for the body-to-chassis mounting points. The rubber is fitted under the body mounting bolt, seated between the body and the chassis...