Land Rover Discovery 1 Parts

Window Motor - LH for the front door electric window regulator system on the Range Rover Classic and Discovery 1. This is the left-hand motor unit...

Lock Nut used to secure interior trim components, including the carpet and sill finishers and the associated bodyside and dust seals. The hex nut ...

Transmitter temperature ORANGE

Temperature switch yellow

Radius Arm Bush Set - polyurethane bushes for the front radius arm mountings at the axle end of the arm, supplied as a set of four in black. The b...

Hexagonal Thin Nut, 7/16" UNF, used within the clutch hydraulic circuit at the master cylinder and pipe connections. The reduced-height (thin) pro...

Wheel Nut for alloy wheel fitment on Defender, Discovery 1 and Range Rover Classic. This tapered-seat wheel nut is designed for use with alloy whe...

Lower Strut Gaiter for the rear self-levelling suspension unit. This flexible rubber boot fits over the lower ball joint of the self-levelling str...

Hex Nut is a metric M5 hexagonal nut used as a general-purpose threaded fastener across multiple vehicle assemblies. It runs onto a matching M5 ma...

Glazing Seal - the glazing rubber that lines the front door window channel and cushions the glass within it. It grips the edge of the glass, holds ...

Front Coil Spring - Medium Duty, +2" Lift (Terrafirma). These front coil springs raise ride height by approximately 2 inches over standard and are...

Decoke Gasket Set - 3.5L V8 - Carb

Differential Flange Mud Shield - a protective shield fitted at the differential pinion drive flange. It sits behind the drive flange, where the pr...

Panhard Rod Bolt with a 1/2" UNF (Unified National Fine) imperial thread and a 3-1/4" shank length, manufactured to a high-tensile grade. Secures ...

Crankshaft Pulley mounts on the front of the crankshaft on the 200TDi 2.5L turbo diesel engine and drives the auxiliary drive belts. This pulley i...

Cleaner Air Filter Element

Bolt - 3/8" UNF x 4-1/4" is a structural fixing used in the front bumper and chassis frame assembly. It secures the front bumper and frame mountin...

Snap Ring retaining the rubber dust boot on a track rod end within the steering linkage. A spring-steel ring that seats in the outer groove of the...

Transfer Box Lever Lock Nut used to secure the selector linkage at the transfer case. This half nut (thin profile locking nut) threads onto the sel...

Brake Pipe Clip from the brake hydraulic pipe routing. It secures and locates a rigid brake pipe against the chassis or body, holding the run of t...

Front Propshaft for 4-cylinder applications, forming part of the drivetrain. It transmits drive from the transfer box front output flange to the fr...

Airflow sensor 4L V-8 engines

Taper Roller Bearing - shaft bearing for the R380 five-speed manual gearbox. A taper roller bearing carries both radial load and axial thrust, loc...

Fan Cowl shrouds the engine cooling fan at the rear of the radiator. It channels the airflow drawn by the fan through the radiator core, improving...

Main Bearing Set for the Rover V8 engine, in the standard size. The main bearings are the crankshaft's principal support bearings, sitting between ...

Seat yoke

Rear Exhaust Bracket - the mounting bracket that supports the rear section of the exhaust system, locating it to the chassis and carrying the tailp...

Gearbox Bearing for the R380 5-speed manual gearbox, measuring 35 × 72 mm. Fitted within the R380 transmission assembly, this rolling-element bear...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...

Gasket - Inlet Manifold - 300TDi

Engine Mounting Rubber (V8) supports the V8 petrol engine on the chassis and isolates its vibration from the bodyshell. The bonded rubber-to-metal...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

Cigar Lighter - the panel-mounted lighter and 12V accessory socket in the instrument panel electrical system. The assembly comprises a socket and ...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

Thermostat for the 2.5L 300TDi diesel engine, operating within the thermostat housing at the top of the cooling circuit. The thermostat regulates ...

Bottom cover seal

Clutch release fork is used in the clutch release mechanism of manual transmission systems. The fork operates within the clutch housing and conve...

Hose pipe valve

Gasket kit 300tdi lower block set no rear crankshaft seal

Brake Pad Set for the front axle disc brake assembly, for use with vented front discs. The pads locate within the front calipers and clamp against ...

Water Pump for the 3.5L Rover V8 petrol engine cooling circuit. Belt-driven from the front of the engine, the pump circulates coolant through the ...

Brake Pad Set for the rear axle disc brake assembly. The pads locate within the rear calipers and clamp against the rear discs, generating the fric...

Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...

Tow Ball 50mm flange-fixing tow ball for use with a bolt-on tow bar drop plate. Rated for a maximum gross trailer weight of 3.5 tonnes, with a D-v...

Starter Motor for the 3.5L V8 petrol engine, operating in the engine starting circuit. When energised through the starter solenoid, the pinion is ...

Coolant Hose - Expansion Tank Vent is the bleed hose in the engine cooling system, connecting the radiator bleed outlet to the coolant expansion ta...

Engine mounting