Land Rover Discovery 1 Parts

Fuel Pump Seal for the fuel tank sender unit. This seal seats at the mounting flange of the fuel pump and sender unit where it interfaces with the ...

Centre Exhaust Silencer located in the mid-section of the V8 exhaust system, between the front downpipe assembly and the rear silencer. Designed f...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Rear Main Bearing Cap Seal for the Rover V8 petrol engine, sealing the joint between the rear main bearing cap and the cylinder block. This crucif...

Oil Pressure Switch - tapered thread, engine lubrication circuit. Screws into the oil gallery - at the pump, the filter housing or the oil cooler ...

Transmission Brake Drum for the transmission (hand) brake. Mounts to the transfer box rear output flange and houses the transmission brake shoes, ...

Blanking Plug for closing a 1-5/8" hole in bodywork or panels. Seals an unused aperture or grommet hole in body panels, brackets and pedal/electri...

Plain Washer in M6 oversize form, with a larger outer diameter than a standard M6 washer. It spreads the clamping load of a bolt head or nut over ...

Plain Washer - metric M8 plain washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...

Front Screen Timer Relay is the grey timer relay within the heated front windscreen circuit. When the heated screen is switched on, this relay ene...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the big-end bearing shells that sit between the connecting rods and the cranks...

Flat plain washer used within general fastening applications across multiple vehicle assemblies, providing a load distribution surface between the ...

Steering Wheel is a 15-inch three-spoke replacement wheel that mounts to the steering column. It is supplied without a boss, so a separate fitting...

Coolant Pipe Adaptor for the engine cooling circuit. It threads into the thermostat housing / cylinder head coolant outlet to provide the connectio...

Heavy Duty spring Range Rover rear +0mm

Hose Clip - 12-20mm worm-drive hose clip suitable for hoses with an outside diameter of 12 to 20mm. This stainless-steel screw-type clip tightens ...

Setscrew is a fully threaded hex-head fastener used as a general-purpose fixing across engine and cooling assemblies. Threaded 5/16" UNC with a 5/...

Track Rod End Boot Ring - spring retaining ring for the track rod end of the steering linkage. It clamps the rubber dust boot onto the track rod en...

A-Frame Ball Joint Boot is the protective gaiter that seals the ball joint at the apex of the rear suspension A-frame. The A-frame locates the rea...

Heater Hose for the V8 EFI petrol engine, forming part of the heater coolant circuit. It carries engine coolant between the heater matrix and the ...

COIL IGNITION GEMS (bobineblok RR 4.6 V8) INTERMOTOR

Exhaust manifold stud

Oil cooler O-ring V8 small

Viscous unit

Clutch Hose for the 300 Tdi 2.5L turbo diesel, forming the flexible section of the clutch hydraulic actuation circuit. The hose links the rigid pi...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

Double Cardan Joint Kit for the Discovery 2 front propshaft. The Discovery 2 front propshaft uses a double cardan joint assembly incorporating thr...

Polyurethane Boot - Defender - Discovery 1/2 - RRC - P38

Differential Pinion Oil Seal with a double sealing lip, for the front and rear differentials. It is press-fitted into the differential housing aro...

Rear Coil Spring Spacers, +2" - a pair of suspension spacers for the rear coil springs that raise ride height by approximately 2 inches (50 mm). E...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

The cable forms the mechanical link between the handbrake operating lever and the handbrake mechanism within the handbrake assembly, transmitting l...

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Silicone Turbo & Intercooler Hose Kit - a three-piece set of silicone charge-air hoses for the 300Tdi turbo and intercooler circuit, replacing ...

Towing Socket Plate for the trailer towing electrics. This mounting plate carries the trailer electrical socket at the rear of the vehicle, provid...

Sump Gasket for the 2.0L MPI T-Series 4-cylinder 16-valve petrol engine, sealing the oil sump to the underside of the cylinder block. It forms the...

Silicone Intercooler & Turbo Hose Kit - a set of silicone charge-air hoses for the 300Tdi turbo and intercooler circuit, replacing the standard...

Toebox Trim Fastener - the fixing that secures the footrest and toebox trim panel in the footwell. It retains the lower trim at the A-post and toe...

Flange Bolt - M8 x 130mm, used to secure the coolant pump (water pump) on the 2.5L 300 TDi diesel engine. The integrated flange beneath the head s...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Split Pin - a cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the shank or the nu...

Body Mounting Kit renews the body-to-chassis mounting points, where the body is located and secured to the chassis frame. The rubber mounts isolat...

Clutch Kit is a matched three-piece clutch assembly for the 3.5L V8 petrol engine with manual transmission. The kit renews the complete clutch as ...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Wash Wipe Switch for the steering column switchgear. This column-mounted stalk operates the windscreen wipers and the windscreen washer. It mounts...