Land Rover Discovery 1 Parts

Fuel Injector within the multi-point injection (MPi) fuel delivery system of the 2.0L T-Series 4-cylinder petrol engine. The injector receives a t...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Upgrade and protect your Land Rover Discovery 1 (3-Door) with this high-quality fibreglass wheel arch extension kit. Designed with notches cut out ...

Throttle Position Sensor (Potentiometer) for V8 petrol engines with Electronic Fuel Injection (EFI). Mounts on the throttle body and signals throt...

Tow Bar Kit - a bolt-on rear towing bracket assembly supplied with wired-in trailer electrics rather than a plug-in socket connection. It provides...

Fuel Injector delivers atomised diesel into the combustion chamber of the 2.5L 300TDi engine. Fitted to non-EGR applications.

Brake servo

Swivel kit OEM Discovery 1 & Range Rover Classic with ABS

Rear Bumper Assembly for the Discovery 1. This is the complete rear bumper unit, fitted to Discovery 1 vehicles built up to (V)LA series. It mount...

Radiator Grille for the front nose panel, sitting within the bumper aperture to cover and protect the radiator core while directing airflow through...

Inner Sill - LH is a structural body repair panel in the lower body assembly of the Discovery 1. The inner sill runs along the base of the door ap...

Inner Sill - RH is the structural steel inner sill section on the right-hand side of the Discovery 1. The inner sill forms the lower edge of the d...

Sill Outer Complete is the full-length outer sill (rocker) panel for the Left Hand (LH) side of the 3-door body. It runs along the lower body bene...

Rear Propeller Shaft for the rear driveline. The propeller shaft transmits drive from the transfer box rear output flange to the rear axle differe...

Camshaft for the Rover V8 EFI petrol engine (3.9L, 4.0L and 4.6L variants). Mounted centrally in the cylinder block, the camshaft is driven from t...

Heater Hose - Outlet returns engine coolant from the cabin heating circuit back to the engine cooling system after it has passed through the heater...

Heater Hose - Inlet carries engine coolant into the cabin heating circuit, feeding the heater matrix that warms air inside the HVAC housing. On th...

Plastic Rivet for use in the rear bumper assembly on Discovery 1. This plastic push-fit rivet secures bumper trim and moulding panels to their mou...

Bulb Holder - Clock Illumination is the socket assembly that seats the illumination bulb behind the dashboard clock, forming part of the instrument...

haynes manual Discovery 1 89>98 Petrol & Diesel (NOT MPI)

Headlamp Wash Pump is the electric motor and pump unit that pressurises the headlamp washer system on the Discovery 1. The pump draws from the win...

Front Wing for the left-hand side. This outer wing panel forms the front bodywork over the wheel arch, locating the front lamps and providing the ...

Autogear Power Syn 75W90 5L

Speedometer Drive Gear in the drivetrain. This gear drives the speedometer cable via the gearbox or transfer case output, translating shaft rotati...

Power Steering Box of the Adwest lightweight type, right-hand drive, supplied complete with the drop arm. The steering box is the mechanical heart...

Washer is an M12 plain flat washer for use with M12 threaded fasteners. Fitted beneath a bolt head or nut, it provides a flat bearing surface that...

Hose Clip is a worm-drive (Jubilee-type) clamp with a 20-30 mm clamping range. Tightened by a captive worm screw, it secures a flexible hose onto ...

Upgrade your Defender, Discovery 1, or Range Rover Classic with this Cellular Dynamic +2" (50mm Lift) rear shock absorber, engineered for exception...

Terrafirma medium load rear springs (pair) 90/D1/RRC

Brake Caliper - front, left-hand side, for the solid (non-vented) front disc arrangement. The caliper carries the brake pads and the hydraulic pis...

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Ignition Module Link Plug - a 3-to-2 pin adapter plug used with the V8 distributor ignition module. It adapts the wiring connection between a 3-pi...

decoke gasket set cylinder head 200TDi engines, WITHOUT head gasket. OEM Elring quality.

Gearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...

Towing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...

Clutch Kit 3.9V8 AP

Hexagonal Plug for the swivel pin housing oil level and drain. This hex-head plug is used in the front axle swivel pin housing as both an oil leve...

Spherical Bush for the LT77 and R380 manual gearbox gearchange mechanism. It seats the spherical pivot at the base of the gear lever inside the re...

Thrust Washer 1.45mm Diff - LT230

Thrust Washer for the differential assembly within the LT230 transfer box. This 1.35mm thrust washer sits within the LT230 centre differential, co...

Rear Stub Axle for non-ABS applications. Bolts to the rear axle case to carry the hub bearings and support the rear hub assembly. For vehicles bui...

Half Shaft Shim is a 1.50mm selective shim used in the axle drive shaft and hub assembly. It sets the endfloat of the half shaft drive member with...

Front flange LT230

Gasket

Exhaust Downpipe with Cat is the front section of the exhaust system for the 300TDi engine, incorporating the catalytic converter. It bolts to the...