Land Rover Discovery 1 Parts

Stainless Steel Braided Brake Hose Kit - Goodridge flexible brake hoses for vehicles built without ABS. Each hose is built around a PTFE inner tub...

Spare Wheel Cover - 235/70 R16 - vinyl cover for an externally mounted spare wheel, sized to a 235/70 R16 tyre. The cover pulls over the assembled...

Top Shock Bush Kit - replacement upper mounting bushes for Pro Sport and 8-stage adjustable remote reservoir shock absorbers. The bushes seat in t...

Shock Ball Joint Kit - service kit for the spherical mounting joint at the end of a performance shock absorber. The ball joint is the principal we...

Plain Washer - flat steel washer from the hardware and fixings group. It is fitted under a bolt head or nut to spread the clamp load over the join...

Wind Deflectors - Set of 4 - Discovery 1

Receiver Hitch Pin - retaining pin for a 2in receiver hitch assembly. The receiver housing has a 2in internal bore that accepts a 2in square-secti...

Internal Spacer for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The spacer fits inside the bump stop to shorten the ...

Valve for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The TF140 is a monotube, nitrogen-charged unit adjustable betw...

Seal Kit - Bump Stop

Nylon Pad for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The pad forms the contact face at the end of the bump stop...

Switch mounting bracket for a single differential lock switch, forming part of the electric locking differential control circuit. The bracket give...

Seal Kit - 11" Travel Shock

Replacement Damper Shaft for the 11 inch travel Mega Sport monotube shock absorber. The shaft carries the damping piston and passes through the se...

Switch mounting bracket for two differential lock switches, forming part of the electric locking differential control circuit. The bracket gives b...

Panhard Rod Bush Kit - replacement polyurethane bush set for heavy-duty adjustable Panhard rods, within the axle lateral-location assembly. The Pa...

Foam Air Filter - Discovery 1 300TDi

Bump stops, standard height - front or rear axle. The bump stop absorbs the last part of suspension compression, cushioning axle-to-chassis contac...

O-Ring - replacement seal for the heavy-duty drive flange centre nut. The O-ring seats between the drive flange body and its removable threaded ce...

Drive Flange Nut - replacement centre nut for the heavy-duty thin-type drive flange, black finish. The drive flange sits at the outer end of the f...

Bulb Holder - Sidelamp is the bulb holder for the sidelamp (front parking lamp) within the exterior lighting system. It retains the sidelamp bulb ...

Inlet Valve for the cylinder head valvetrain of the 3.5 V8 carburettor petrol engine. The inlet valve seals the intake port against combustion pre...

Screw - threaded fastener specified in two unrelated assemblies: securing components to the cylinder block of the 2.5L 5-cylinder turbo diesel engi...

Hex Socket Screw, M8 x 20 - hexagon socket head fixing screw. Used on diesel engine installations at points where a conventional hexagon head cann...

Piston Ring Set - 0.020in Oversize - 300TDi

Wire - Ignition

Piston Ring Set - 0.020in Oversize - 300TDi

Front Headlamp - Left-Hand - the complete headlamp unit for the left-hand side of the front lighting assembly, comprising the reflector, lens and b...

Non-Return Valve - Brake Vacuum - the one-way valve in the vacuum line between the engine and the brake servo, part of the master cylinder and serv...

Front Headlamp - Right-Hand - the complete headlamp unit for the right-hand side of the front lighting assembly, comprising the reflector, lens and...

Radius Arm Bush Kit - yellow polyurethane replacement bushes for the front end of the rear radius arm, at the point where the lower link mounts int...

Gasket Sealant - a non-setting jointing compound to the Hylomar 2000 specification, used on engine and transmission joint faces where a liquid seal...

Service Kit for the 3.9L V8 EFI petrol engine, grouping the scheduled lubrication, induction and fuel filtration items into a single pack. The kit...

Major Service Kit for the 200 TDi 2.5L four-cylinder turbo diesel, grouping the scheduled lubrication, induction and fuel filtration items into a s...

Major Service Kit for the 200 TDi 2.5L four-cylinder turbo diesel, grouping the scheduled lubrication, induction and fuel filtration items into a s...

Pivot Pin a machined clevis-type pin that forms the hinged joint between a linkage rod and its bracket or lever. The pin passes through the clevis...

Main Bearing Set for the crankshaft main journals of the 2.5 litre four-cylinder diesel engine (naturally aspirated, turbo diesel, 200 Tdi and 300 ...

Key Wheel Nut

Hydraulic Tappet Assembly for the cylinder head valvetrain of the 2.5-litre four-cylinder engine range, forming the mechanical interface between th...

Main Bearing Set, standard size, in copper-lead bearing material, for the crankshaft main journals of the 2.5 litre four-cylinder diesel engine (na...

Swivel Housing Seal Kit - Front Axle

Fuel Filter Element for diesel applications - the replaceable filtration cartridge that fits inside the fuel filter housing in the low-pressure fue...