Land Rover Discovery 1 Parts

Exhaust Silencer for the Discovery 1 exhaust system. This is the rear silencer for the non-catalyst exhaust configuration, fitted to vehicles buil...

Pipe Clamp for the engine oil cooler pipe circuit. This clamp plate secures the oil cooler pipes in the engine bay, restraining them against vibra...

Exhaust Silencer for the 200Tdi 2.5L Turbodiesel exhaust system, non-catalyst specification. Fits in the mid-to-rear section of the exhaust system...

Radiator Top Hose for the 200TDi 2.5L turbo diesel cooling circuit. Connects the engine outlet at the thermostat housing to the top inlet of the r...

Fuel Filter Assembly within the diesel fuel supply circuit, removing contaminants from the fuel before it reaches the injection system. Installed ...

Track Rod Adjusting Shaft is the threaded centre bar of the steering track rod assembly, into which the track rod ends are screwed. Rotating the s...

Coil Spring - Front for the front suspension of the Discovery 1 and Range Rover Classic. The front coil spring seats between the front axle casing...

Drag Link Tube The central tube of the drag link in the steering linkage. The drag link transmits steering movement from the steering box drop arm...

Starter Motor for the 2.5L 4-cylinder diesel engine, part of the engine electrical starting circuit. When the ignition is operated the solenoid th...

Bonnet cable

Engine Oil Sump for the 2.5L 300 TDi turbo diesel, part of the engine lubrication system. The sump bolts to the underside of the cylinder block an...

spring synchro FTC4992

Brake Fluid Reservoir Overhaul Kit for the brake master cylinder on ABS-equipped vehicles. The kit is used to renew the fluid reservoir section of...

Battery Tray is the offside (right-hand) carrier tray that supports and locates the battery in the engine bay. It forms the mounting platform on w...

Flange Nut - M10 Nyloc is an M10 x 1.5 nylon-insert flange nut used on the exhaust system, securing the joints between the turbocharger or manifold...

MOUNTING - BOTTOM LINK - REAR - PAIR

Washer

Rear Propshaft Rubber Coupling - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while ab...

Monotube Suspension Kit - standard ride height, standard load. A matched set of shock absorbers and coil springs covering both axles, grouped under...

Coil spring trim spacers, 5 mm, fitted between the lower spring mounting plate and the axle to make fine ride height adjustments. Spacers are stac...

All Terrain Suspension Kit - standard ride height, standard load. A matched set of shock absorbers and coil springs covering both axles, grouped un...

Terrafirma All Terrain Suspension Kit - Heavy Load - Standard Height - Defender 90/Disco 1/RRC

Conrod Bolt

oil sump for classic Rover V8 engines

Drive Belt is the serpentine (poly-vee) accessory belt for the 4.0L V8 EFI petrol engine fitted with air conditioning. Driven from the crankshaft ...

PAS pump seal kit

H4 Spare Bulb and Fuse Kit for 12V vehicles with H4 headlamps, holding replacement bulbs for the main exterior lamps and spare blade fuses in a com...

PUMP - WATER - ENGINE COOLING 300TDi

Spark Plug for the ignition system of 2.5L 4-cylinder and 3.5L V8 petrol engines. The plug seals the combustion chamber and carries high-tension v...

Universal Joint for the propeller shaft, measuring 75 mm across the bearing caps with a 27 mm cap diameter. Sealed type, supplied without a grease ...

Relay is a 12V 40 A normally open (make-contact) relay used across the body and engine electrical circuits. Energising the control coil closes the...

Cigar Lighter Assembly - facia-mounted 12V cigar lighter, comprising the socket body and the heating element that seats in it. The element is push...

Transfer Box Switch Wire Adaptor for the LT230 transfer gearbox. This short harness link connects the main vehicle wiring loom to the switch on th...

Front Axle Reinforcing Kit - a two-piece set of pre-cut, weld-on reinforcing sections for the front axle casing, profiled to suit the long-nose Rov...

Stainless Steel Braided Brake Hose Kit - Goodridge flexible brake hoses for vehicles built without ABS. Each hose is built around a PTFE inner tub...

Spare Wheel Cover - 235/70 R16 - vinyl cover for an externally mounted spare wheel, sized to a 235/70 R16 tyre. The cover pulls over the assembled...

Top Shock Bush Kit - replacement upper mounting bushes for Pro Sport and 8-stage adjustable remote reservoir shock absorbers. The bushes seat in t...

Shock Ball Joint Kit - service kit for the spherical mounting joint at the end of a performance shock absorber. The ball joint is the principal we...

Plain Washer - flat steel washer from the hardware and fixings group. It is fitted under a bolt head or nut to spread the clamp load over the join...

Wind Deflectors - Set of 4 - Discovery 1

Receiver Hitch Pin - retaining pin for a 2in receiver hitch assembly. The receiver housing has a 2in internal bore that accepts a 2in square-secti...

Internal Spacer for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The spacer fits inside the bump stop to shorten the ...

Valve for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The TF140 is a monotube, nitrogen-charged unit adjustable betw...

Seal Kit - Bump Stop

Nylon Pad for the TF140 hydraulic bump stop, part of the suspension bump stop assembly. The pad forms the contact face at the end of the bump stop...

Switch mounting bracket for a single differential lock switch, forming part of the electric locking differential control circuit. The bracket give...

Seal Kit - 11" Travel Shock