Land Rover Discovery 1 Parts

Rear Lamp Guard Set is a pair of protective guards for the rear lamp units. The guards fit over the rear light clusters to shield the lenses from ...

Propshaft Gaiter is the rubber boot that seals the sliding (slip) joint of the propshaft, retaining grease on the splines and excluding water, grit...

Synchroniser Kit - 5th/Reverse Gear for the R380 five-speed manual gearbox, serving the mainshaft 5th gear and reverse gear assembly. The synchron...

Heater Blower Speed Resistor sets the lower fan speeds of the heater and ventilation blower in air-conditioned applications. Wired in series with ...

Touch-Up Paint Pencil applies the Epsom Green body colour to small stone chips and scratches in the paintwork. The pencil applicator gives accurat...

Headlamp Mounting Panel is the right-hand front body panel that carries the headlamp unit. It provides the aperture and fixing points that locate ...

Starter Solenoid for the engine cranking circuit, mounted on the starter motor body. When energised by the ignition switch it throws the starter p...

Cylinder Block Screw is a threaded fastener used on the V8 EFI petrol cylinder block assembly. It secures ancillary components and mounting bracke...

Instrument Cluster Bulb Holder for the instrument cluster, part of the cluster illumination and warning-light circuit. The holder pushes into the ...

Touch-Up Paint Pencil in the metallic colour Arken Grey (Micatallic), paint code LRC445. A brush-applicator pencil for precise touch-up of stone c...

Blanking Plug used to close off an unused aperture in the body or panel work, part of the grommets and blanking group. It seals a redundant or opt...

Heater Assembly Clip A retaining clip used within the heater (HVAC) assembly to hold adjoining components of the heater box together. It secures t...

Layshaft Roll Pin for the manual transmission. This roll (tension) pin locates and retains the layshaft within the gearbox casing, holding the sha...

Battery Mounting Panel The pressed panel that forms the base on which the vehicle battery is seated and secured. It locates and supports the batte...

Piston Assembly for the 3.5-litre Rover V8 petrol engine, supplied at 0.020" oversize for a rebored cylinder block. It locates in the cylinder bore...

Door Lock Clip is a retaining clip that operates within the rear end door lock assembly. It secures the lock components in position within the rea...

Door Lock & Handle Retaining Clip - securing clip within the exterior door handle and lock assembly. This clip retains the door lock and handl...

Rear Bumper Mounting Bracket secures the rear bumper to the chassis, carrying the bumper load into the vehicle structure. Part of the rear body an...

Rocker Shaft Spring for the 2.5L 200 TDi diesel engine, fitted on the rocker shaft within the valve train. The spring spaces the rocker arms along...

Braided Brake Hose Kit for the front and rear brake hydraulic circuit, replacing the flexible rubber hoses with stainless-steel braided lines. This...

Track rod end pin nut for the steering linkage. Secures the tapered pin of the TRE 80 track rod end into the steering arm eye, clamping the taper ...

Plain Washer, an M6 flat washer. It fits under the head of an M6 bolt or nut to spread the clamping load over a wider bearing area and protect the...

cable accelerator ANR4617

Washer - a general-purpose fastener washer used across a number of assemblies, including facia, fuel injection, sunroof and interior lamp fixings. ...

Main Bearing Set - .010" Oversize is the set of crankshaft main bearing shells that carry the crankshaft in the cylinder block, supplied 0.010 in o...

Grab Handle is the rear pillar (E-post) bodyside grab handle, part of the body-side trim and handle assembly. It fixes to the rear pillar to provi...

Label "ONE"

Front Indicator Lamp for the left-hand side, part of the front lighting assembly. Provides the front direction-indicator (turn signal) function on...

Door Lock Circlip - retaining clip for the rear end door lock. This circlip secures a component of the rear door lock mechanism, holding it on its...

Spring Nut is a sheet-metal fastener used in body panel and interior trim assemblies. It clips over a panel edge or into a pre-formed hole to prov...

Door Hinge Assembly mounts a side door to the body and allows it to pivot open and closed. The assembly bolts between the body pillar and the door...

Tailgate Body Tape - a self-adhesive decal fitted to the tailgate as part of the exterior body trim.

Gear Lever Gaiter for the centre console. This flexible boot fits around the base of the gear lever where it passes through the console, covering ...

Rear Bumper Step Mat - the moulded rubber tread that fits to the top face of the rear bumper. It provides a non-slip surface where the bumper is u...

Door Waist Seal - waistline weatherstrip running along the lower edge of the door glass aperture, part of the rear side door and glass sealing asse...

Escutcheon - finishing surround for the rear end door lock barrel, part of the rear door lock and casing assembly. It fits over the lock cylinder ...