Land Rover Discovery 1 Parts

Drive Belt for the V8 petrol engine auxiliary drive - a 7-rib poly-V (7PK) serpentine belt measuring 1870 mm. Transfers crankshaft rotation to the...

Front Left-Hand Indicator Lamp Assembly for the Discovery 1. This amber turn signal lamp unit is mounted at the front left corner of the vehicle a...

O-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...

Coolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...

Brake Valve for the front brake hydraulic circuit. Regulates hydraulic pressure to the front brakes and is used on both ABS and non-ABS systems.

Flanged Nut - M10 flanged fastener. The integral flange spreads the clamping load over a wider area and resists loosening under vibration, removin...

Shock Absorber A hydraulic telescopic shock absorber (damper) for the front suspension. It damps spring oscillation to control body movement and m...

Raised Air Intake Mantec - 90/110 200TDi

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Drive Belt Air conditioning compressor drive belt for the 200TDi turbo diesel engine, poly-vee (multi-rib) construction. Drives the A/C compressor...

Belt - Polyvee - Petrol

Brake Hose - Front is a flexible hydraulic hose in the front brake circuit, connecting the rigid chassis-mounted brake pipe to the front brake cali...

Cylinder Head for the 300 TDi 2.5L four-cylinder turbo diesel engine, supplied as a bare casting without valves. The head bolts to the top face of...

Front Half Shaft for the right-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant vel...

Front Axle CV Joint, heavy-duty, 24-spline, for the front drive shaft. The constant velocity joint sits at the outer end of the front axle shaft an...

Hose - Oil

Brake Caliper Rear - RH

Brake Master Cylinder - ABS is the tandem master cylinder at the head of the hydraulic braking circuit, specified for the servo-assisted anti-lock ...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Air Filter Element installed in the air cleaner housing of the 200Tdi 2.5L four-cylinder turbo diesel engine. The element filters intake air upstr...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Camshaft Oil Seal - radial oil seal for the 2.5L 300 TDi turbo diesel engine, fitted in the front timing cover within the timing gear assembly. Th...

Connecting Rod Bearing Set for the 2.5L 4-cylinder engine, supplied in 0.030" oversize. These are the big-end shell bearings that fit between the ...

Oil Filler Cap closing the engine oil filler neck on the rocker cover. It seals the filler aperture to keep the lubrication system closed and prev...

Tow Ball Step is a rear access step that locates over the tow ball, providing two tread levels to make reaching the rear door, load area or roof ea...

Gasket Set

Coupling - Viscous Borgwarner

Air Filter Element for the 3.5L V8 Twin Carb petrol engine air intake. This filter element is fitted in the air intake housing ahead of the carbur...

Swivel Joint Washer located within the Swivel Pin Housing Assembly, sealing the interface between the swivel housing flange and the axle beam face....

Exhaust Manifold Gasket for the 200 TDi diesel engine, sealing the joint between the exhaust manifold and the cylinder head. It seals each exhaust...

Wheel Bearing Kit - Front and Rear

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Layshaft Bearing - taper roller bearing supporting the layshaft in the R380 5-speed manual gearbox. The bearing carries the countershaft (layshaft...

Camshaft Seal - Rear

Piston Assembly - +0.020" Oversize for the 300Tdi 2.5L 4-Cylinder Turbo Diesel engine. This piston is machined to a diameter 0.020" (approximately...

Fuel Injector for the 2.5L 300TDi 4-cylinder turbo diesel engine. This direct injection fuel injector delivers metered, atomised fuel into the pre...

Oil Seal for the R380 manual gearbox extension case (rear/tail housing). It seals the output shaft where it exits the extension housing, retaining...

Connecting Rod Bearing Set for the 2.5-litre 4-cylinder engine, including the 200 TDi and 300 TDi diesels. These are the replaceable big-end shell ...

Engine Mounting Bracket - 3.5L V8

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...